Directed Directechs DS3 Installation Manual Download Page 2

Page: 2 / 27

Introduction

Vehicle function compatibilities

Pre-installation and application warnings

Installation

Wiring diagram with T-Harness (THFON1)

Wiring diagram

Locating components in the vehicle

Module programming for convenience only (skip transponder)

Module programming for security-only installations

Pairing remotes

Connecting the module

8556T Temperature Sensor

8504D Combo Sensor

RF Systems

When used in conjunction with SmartStart

D2D port configuration

Manual transmission

LED diagnostics and troubleshooting

Soft reset

Hard reset

Tach learning procedure (not needed with Virtual Tach)

Initializing Virtual Tach (not needed with hardwired or data tach applications)

Limited lifetime consumer warranty

Quick Reference Guide

Contents

Summary of Contents for Directechs DS3



























Search results

Summary of Contents for Directechs DS3

Reviews:

Related manuals for Directechs DS3

Brands by name

Popular brands

Directed Directechs DS3, Installation Manual

Search results

Summary of Contents for Directechs DS3

Reviews:

Related manuals for Directechs DS3

Brands by name

Popular brands