Directed Directechs DS3 Installation Manual Download Page 5

Page: 5 / 27

933.FORD6 3.24.195.3 2010 Lincoln MKS
©2022 VOXX•DEI LLC. All rights reserved.

Pre-installation and application warnings

Firmware notes:

This section highlights important information for this specific firmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

THFON1

Keys required for

programming

1 or 2

Keys required for

operation

The optional Plug & Play

THFON1

T-Harness is sold separately.

The

THFON1

ONLY

compatible with the DS4+ and is

NOT

compatible with the DS4 Lite.

All T-Harness wires

NOT

listed in the diagram are

NOT

required for the installation. Loose wires such as Siren Output and

Hood Input may need to be pulled from the tapped section of the T-harness. Refer to the "wiring diagram with T-Harness" for

more information on connections and installation instructions.

Key2GO is required if only one key is available. You can program the interface with out the need for Key2GO if two keys

are present.

Keys required to program:

40-bit PATS is Key2GO compatible and module programming can be done using

1 or 2 different master keys

Refer to the "Understanding the difference between a Ford 80 & 40 bit" section for more information.

The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic

connector.

It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each

wiring diagram.

Refer to the "Vehicle connections" following the installation diagram.

General notes:

This section highlights important information for this specific firmware.

[1]

The installation of an aftermarket hood pin is

ONLY

required on vehicles that are

NOT

equipped with a factory hood pin.

[2]

The siren is

ONLY

required when enabling the security features during module flashing.

[3]

Connections

ONLY

required if features do not operate in data.

[4]

ONLY

required if OEM alarm equipped.

[5]

For Security Only installations, refer to the "Locating components in the vehicle" section for the optional starter disable

connection.This connection is

NOT

required when using the

THFON1

T-Harness.

Summary of Contents for Directechs DS3



























Search results

Summary of Contents for Directechs DS3

Reviews:

Directed Directechs DS3, Installation Manual, Page: 5 / 27

Search results

Summary of Contents for Directechs DS3

Reviews: