background image

15

933.FORD6 3.24.195.3 2010 Lincoln MKS
©2022 VOXX•DEI LLC.  All rights reserved.

 

1 Key required! 

1

Ensure vehicle is in a safe location and cannot move forward during programming. For
vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral
position.

2

DS3+: Connect the 12-pin main power harness to the module FIRST.
Wait until the LED turns ON solid red before proceeding to the next step.

DS4+: Connect the 12-pin main power harness to the module FIRST.
The LED will turn ON solid blue for 1 second to confirm Bluetooth communication.
Wait until the LED turns ON solid red before proceeding to the next step.

3

Connect the remaining harnesses to the DS4+ module.

4

Insert and turn the key to the ON and OFF twice. 
The LED starts flashing orange slowly.

5

Turn the ignition off by removing the key from the ignition barrel, remove the module from

the vehicle and reconnect it to your computer.

The website will automatically recognize that you are moving onto the second phase

of the programming sequence.

1.

Click Submit Key2GO Request.

2.

6

When the configuration is completed, reconnect the module.
The LED will turn on solid green for 3 seconds, then turn off.

7

Pair remotes (if applicable). 

For information on how to pair a specific remote, please refer to its corresponding owner
documentation, which can be found inside the product packaging of the complete system or
on www.directechs.com.*

8

DATA/Hardwired Tach Learning: When using Data Tach, it is recommended to follow the
Tach Learning procedure. However, when using a Hardwired Tach, the procedure is
mandatory.
 
For more information, refer to the Tach Learning procedure section.

* Your aftermarket remote may differ from the model shown in the illustrations.

You have successfully completed the module programming sequence.

Summary of Contents for Directechs DS3




























Reviews: