Directed Directechs DS3 Installation Manual Download | Manualshive

Page: 19 / 27

background image

19

933.FORD6 3.24.195.3 2010 Lincoln MKS
©2022 VOXX•DEI LLC. All rights reserved.

When used in conjunction with Directed SmartStart

®

To enable D2D communication between the DS3+/DS4+ and the Directed SmartStart

®

one of the following actions must be performed

before providing power to the Directed SmartStart

®

unit:

SmartStart with

Loops

– The brown loop must be cut.

SmartStart with

Pigtails

– The gray wire must be connected to a ground source.

Loops

Pigtails

DO NOT

connect the Directed SmartStart

®

2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the

D2D connector on the module. Refer to the Directed SmartStart

®

documentation for further details.

D2D port configuration

Caution!

Do not connect the Control Center (antenna) or any digital sensors (8504D) to the white D2D1 port.

The white D2D1 port is reserved ONLY for SmartStart, Module flashing or 3rd Party bypass. The two black D2D2 ports are reserved for the
Control Center (antenna) and digital sensors (8504D).

«
...
17
18
19
20
21
...
»

Summary of Contents for Directechs DS3




























Reviews:

No comments

Related manuals for Directechs DS3

Brand: ABB Pages: 14

Brand: Acer Pages: 2

Brand: Acer Pages: 4

Brand: Kargo Master Pages: 5

Brand: Kappa Pages: 4

Brand: Manfrotto Pages: 2

Brand: Zen Underwater Pages: 3

WV7220D - CCTV ACCESSORIES

Brand: Panasonic Pages: 10

WV-NS202 - i-Pro Network Camera

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 4

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 19

Brand: Panasonic Pages: 59

Brand: Zacuto Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands