background image

D I R E C T H E A L T H C A R E S E R V I C E S . C O . U K

6

D Y N A - F O R M   M E R C U R Y   A D V A N C E

5. Operation 

Attach the mains cable to the pump by inserting the “kettle” type connector into the recess  

on located on the left hand side of the pump. The mains cable has been designed specifically  

as a removable part to aid in easy replacement should it become damaged in use. 
The mains plug should be turned off and removed from wall socket as a means of isolation.
Plug the mains cable into a suitable 230v mains socket and switch on the Power Unit using the on/off switch. 
After the pump has been turned on both the “Hi “and the “Lo” lights will flash together intermittently 

until the pump has attained its initial operating pressure. Once the pump has attained its initial 

operating pressure the “Lo” light will stay on constantly and the mattress is ready for use. 

5.1. Lo / Hi Settings 

The Dyna-Form® Mercury Advance Mattress, in Alternating Mode, has two pressure settings.  

The initial setting that the pump will revert to upon set up is “Lo”. The “Lo” comfort setting is ideal 

for the lighter patient of those who feel discomfort when on a normal alternating air type mattresses 

system. However, for patients with existing pressure damage or those at Very High Risk, it is 

recommended that dependant on the clinical judgement of the clinician, the “Hi” setting is activated 

by pressing the +/- button once, which is located on top of the pump. 
In “Hi” Mode the pump attains more of the characteristics of an alternating air mattresses system 

whilst still utilising the advantages of the static foam inserts. Repeatedly pressing the ‘mode’ button 

enables the Lo & Hi modes to be selected in turn. 

5.2. CPR Deflation 

The CPR system consists of a manually operated button located on the Air Inlet connector attached 

to the pump. By pressing the Red Button, which will release the connector locking system, the user 

can remove the connector unit which will deflate the mattress air system back to that of a static 

foam mattress. 

Note: After a short period as the Mattress deflates the ‘Low Pressure’ Audible Warning is activated and can be cancelled 

by switching the Power Unit off. 

5.3. Troubleshooting

For assistance (if needed) in setting up, using or maintaining the Mercury Advance System, or to 

report unexpected operation or events, please contact Direct Healthcare Services on the contact 

details on the reverse of this manual.

6. Transportation

To change the location of the mattress, remove the Umbilical cord and allow the mattress to 

return to its Static Mattress form. Switch off the Power Unit (Pump) using the on/off switch and 

disconnect the electrical supply cable from the mains socket. The mattress can now be moved to 

a new location where it must immediately be reconnected to the mains electrical supply and the 

Power Unit (Pump) switched back on. Once the Mattress has been refilled, the ‘Alternating’ mode 

will automatically revert back to the Lo setting and should be reselected to Hi should this be desired 

by the clinician.

Warning: The Mattress will not ‘alternate’ when disconnected from the Power Unit (Pump) and /or the mains electrical. 

Also refer to environmental conditions section at rear of this manual.

Summary of Contents for Dyna-Form Mercury Advance

















Reviews: