DINGLI JCPT2223RT Operators Manual With Maintenance Information Download

Page: 58 / 74

OPERATOR

’S MANUAL

with Maintenance Information

Maintenance

B-12

Perform Hydraulic Oil Analysis

Dingli requires that this procedure be

performed every 250 hours or quarterly,

whichever comes first.

Replacement or testing of the hydraulic oil is

essential for good machine performance and

service life. Dirty oil and a clogged suction

strainer may cause the machine to perform

poorly and continued use may cause

component damage. Extremely dirty

conditions may require oil changes to be

performed more often.

Note: Before replacing the hydraulic oil, the oil

may be tested by an oil distributor for specific

levels of contamination to verify that changing

the oil is necessary. If the hydraulic oil is not

replaced at the two year inspection, test the oil

quarterly. Replace the oil when it fails the test.

See E-1, Test or Replace the Hydraulic Oil.

B-13

Perform Engine Maintenance

Engine specifications require that this

procedure be performed every 250 hours or

quarterly, whichever comes first.

Required maintenance procedures and

additional engine information is available in the

engine operator

’s manual.

B-14

Perform Drive Axle Maintenance

Axle specifications require that this procedure

be performed every 250 hours or quarterly,

whichever comes first.

Required maintenance procedures and

additional Axle information is available in the

Axle operator

’s manual.

Summary of Contents for JCPT2223RT











































































Search results

Summary of Contents for JCPT2223RT

Reviews:

Related manuals for JCPT2223RT

Brands by name

Popular brands

DINGLI JCPT2223RT, Operators Manual With Maintenance Information

Search results

Summary of Contents for JCPT2223RT

Reviews:

Related manuals for JCPT2223RT

Brands by name

Popular brands