Dimplex WI 120TU, Installation And Operating Instruction

Page: 34 / 84

EN-14 452237.66.53 · FD 9912 www.gdts.one
English WI 120TU - WI 180TU
9 Heat output / COP
9.1 Heat output / coefficient of performance (COP)
3 6
EN 14511
Performance level 1 2
at W10 / W55 kW / --- 52.1 / 3.7 104.2 / 3.7
at W10 / W45 kW / --- 55.9 / 4.7 109.5 / 4.6
at W10 / W35 kW / --- 61.6 / 6.1 118.5 / 5.9
1. The specified sound pressure level corresponds to the operating noise of the heat pump in heating operation at 55 °C flow temperature.
The specified sound pressure level represents the free sound area level. The measured value can deviate by up to 16 dB(A), depending on the installation location.
2. Note that additional space is required for pipe connections, operation and maintenance.
3. These data indicate the size and capacity of the system according to EN 14511. For an analysis of the economic and energy efficiency of the system, the bivalence point and
regulation should be taken into consideration. These specifications can only be achieved with clean heat exchangers. Information on maintenance, commissioning and oper-
ation can be found in the respective sections of the installation and operating instructions. The specified values, e.g. W10 / W55, have the following meaning: Heat source
temperature 10 °C and heating water flow temperature 55 °C.
4. See CE declaration of conformity
5. The heat circulating pump and the heat pump manager must always be ready for operation.
6. The coefficients of performance are valid with the circulating pumps included in the scope of supply.
1 Type and order code
WI 180TU
2 Design
Heat source Water
2.1 Model Universal
2.2 Controller integrated
2.3 Thermal energy meter Integrated
2.4 Installation location Indoors
2.5 Performance levels 2
3 Operating limits
3.1 Heating water flow °C 20 to 62 ± 2
3.2 Cold waterRC (heat source) °C +7 to +25
4 Flow / sound
4.1 Heating water flow / free compression (max).
Nominal flow in accordance at W10...7 / W35...28 m³/h / Pa 22.2 / 40000
at W10...7 / W45...38 m³/h / Pa 21.2 / 43500
at W10...7 / W55...45 m³/h / Pa 14.4 / 64000
Minimum heating water flow m³/h / Pa 14.4 / 64000
4.2 Cold water flow rate / internal pressure differential
Nominal flow in accordance at W10...7 / W35...28 m³/h / Pa 42.1 / 41500
at W10...7 / W45...38 m³/h / Pa 37.2 / 32500
at W10...7 / W55...45 m³/h / Pa 34.7 / 28000
Minimum cold water flow rate m³/h / Pa 34.7 / 28000
4.3 Sound power level according to EN 12102 dB(A) 70
4.4 Sound pressure level at a distance of 1m
1
dB(A)
55
5 Dimensions, weight and filling quantity
5.1 Device dimensions
2
H x W x L mm
1890 x 1350 x 750
5.2 Weight of the transportable unit(s) incl. packaging kg 824
5.3 Device connections for heating inches Rp 2½“
5.4 Device connections for heat source Inches Rp 3“
5.5 Refrigerant / total filling weight type/kg R410A / 19.5
5.6 GWP value / CO
2
equivalent --- / t
2088 / 41
5.7 Refrigeration circuit hermetically sealed yes
5.8 Lubricant / total filling quantity type/litres Polyolester (POE) / 14.6
5.9 Volume of heating water in device Litres 26
5.10 Volume of heat transfer medium in device Litres 26
6 Electrical connection
6.1 Supply voltage / fuse protection / RCD-Type 3~/PE 400 V (50 Hz) / C 100A / A
6.2 Control voltage / fuse protection / RCD-Type 1~/N/PE 230 V (50 Hz) / C 13A / A
6.3 Degree of protection according to EN 60 529 IP 21
6.4 Starting current with soft starter A 110
6.5 Nominal power consumption W10 W35 / max. power consumption
3
kW
32.1 / 57.5
6.6 Nominal current W10 W35 / cos  A / --- 57.9 / 0.8