Dilog DL9120 Operating Instructions Manual Download Page 35 | Manualshive

Page: 35 / 43

Dilog DL9120 Operating Instructions Manual Download Page 35

DL9120 / DL9130

Operating Instructions

- 35 -

TEST

To start a test press the TEST key, the test will be performed and the trip
current of the RCD will be displayed in the primary display. In variable
mode the RCD test current performed meets the current specification for
the x1 test.

5.14 Warning / Test Active Indications

The following indications are used across a number of functions in the
DL9120 / DL9130EV.

Indicates that the DL9120 / DL9130EV is hot.
Please allow to cool before proceeding.

Indicates that a hazardous test is in progress with by
the DL9120 / DL9130EV.

Indicates that a hazardous test voltage is being
generated by the DL9120 / DL9130EV.

Mains status indications. Static icons indicate that
the voltage is present and correct, flashing indicates
an incorrect voltage present.

Battery level. Flashing indicates that the battery
needs replacing.

This icon may appear during test, this will animate
indicating that the test is in progress. Please leave
DL9120 / DL9130EV to allow test to complete.

«
...
33
34
35
36
37
...
»

Summary of Contents for DL9120












































Reviews:

No comments