manualshive.com logo in svg

Dilog DL9120, Operating Instructions Manual, Page: 16 / 43

Share
Download
Dilog DL9120 Operating Instructions Manual Download Page 16

DL9120 / DL9130        

                                           Operating Instructions 

- 16 - 

5  Using the DL9120 / DL9130EV 

 

5.1  Power On 

To turn the DL9120 / DL9130EV on, simply rotate the rotary switch to the 
required  test  position,  the  DL9120  /  DL9130EV  will  display  the  battery 
voltage for a short period of time. 
 

Backlight Functionality (Power On with F1 pressed) 

If  F1  is  held  down  when  turning  on  the  DL9120  /  DL9130EV  then  the 
backlight options will be displayed. The DL9120 / DL9130EV will display 

bL

 and the existing setting, pressing F1 will cycle through the available 

options; 
 
 

OFF 

- Backlight functionality is disabled 

bLUE  - The backlight is always set to blue 
rGb 

- LCD backlight is set to blue but will change to green for 
passed measurements and red for failed measurements. 

 
Press the test key to store the displayed option.   
 

Battery Health Check 

The DL9120 / DL9130EV will automatically perform battery health checks 
at power on and periodically while the DL9120 / DL9130EV is being used. 
  

Note: When the battery symbol is flashing all tests will be inhibited 

and the batteries should be replaced as described in section 
8.4. 

 
Note: The battery  health check  may  indicate  that  the batteries  are 

healthy  but  stop  tests  with  a  flashing  battery  symbol  during 
testing. This is due to the different levels of current required 
during different test types.  The  batteries  should be  replaced 
as described in section 8.4. 

 

5.2  Remote probe (only supplied with DL9130EV) 

The  remote  probe  can  be  used  in  place  of  the  standard  4mm  red  test 
lead. When the remote probe is connected, the TEST button on the probe 
performs the same function as the TEST key on the DL9120 / DL9130EV. 
Either TEST button/key can be used to initiate a measurement.   
 
 
 
 

 

Summary of Contents for DL9120












































Reviews:

No comments