manualshive.com logo in svg

Dilog DL9120, Operating Instructions Manual, Page: 33 / 43

Share
Download
Dilog DL9120 Operating Instructions Manual Download Page 33

DL9120 / DL9130        

                                           Operating Instructions 

- 33 - 

   

 

RCD Type AC Selective (Sinusoidal Waveform) 

    

RCD Type A (Pulsating Waveform) 

   

 

RCD Type A Selective (Pulsating Waveform) 

 

RCD Type B (DC) 

 
During selective tests, the DL9120 / DL9130EV will display a delay timer 
which counts down from 30s to 0s. Pressing the Test key or turning the 
rotary switch while the DL9120 / DL9130EV is counting will terminate the 
count. 

 
Increase Test Current (F4) 

Increases the test current displaying the secondary display. 
 

Decrease Test Current (F4) 

Decreases the test current displaying the secondary display. 

 
TEST 

To start a test, press the TEST key, the test will be performed and the trip 
current of the RCD will be displayed in the primary display. 
 
 
 

5.13  RCD trip current (Ramp) Tests 

 

 

The DL9120 / DL9130EV will only allow the RCD test to be 
performed if the correct voltages are detected between line-
earth (L-PE illuminated), line-neutral (L-N illuminated) and 
neutral-earth (N-PE 

not

 illuminated).  

  

 

Potential  fields  from  other  earthing  installations,  large 
voltages between the protective conductor and earth, large 
voltage between the neutral and earth or leakage currents 
in the circuit following the residual current protection device 
may influence the measurement. 
 

 

Equipment  which  is  connected  downstream  of  a  residual 
current protective device (RCD) may cause a considerable 
extension of the operating time. 
 

 

The  DL9120  /  DL9130EV  will  determine  the  fault  voltage 
that may appear on the protective conductor during the test. 
If  the  fault  voltage  is greater  than  25V  the  DL9130EV  will 

Summary of Contents for DL9120












































Reviews:

No comments