Digital Equipment LN15 User Manual Download Page 107

Page: 107 / 122

DIGITAL Laser Printer LN15 User Manual

5-18

Warning
Messages

This printer counts the number of the printed sheets to estimate the life
of the consumables (print unit). The printer indicates the following
warning message when and after the count reaches a predetermined value.

READY REPLACE PARTS

When the warning message is indicated, press the

READY

button to put

the printer offline and press the

button to enter menu mode. The

Clear Warning message appears, indicating the expired unit by an
asterisk. When the print unit is expired, the message is:

<CLEAR WARNING> PRINT UNIT*

However, depending on the print quality, you may not have to replace
the print unit because you may still be satisfied with the print quality.

Summary of Contents for LN15



























































































































Search results

Summary of Contents for LN15

Reviews:

Related manuals for LN15

Brands by name

Popular brands

Digital Equipment LN15, User Manual

Search results

Summary of Contents for LN15

Reviews:

Related manuals for LN15

Brands by name

Popular brands