2
INTRODUCTION TO YOUR LEIT LINK
LEIT LINK HANDSET COMPONENTS
1. LCD Display
Displays the application stored in your handset.
2. Power Button
Turn your LEIT Link on or off
.
3. Programming Buttons
Use these 4 buttons to program, modify, review and communicate with the LEIT XRC controller.
Use to accept and/or select the desired programming mode and raise (increase) the value of
the selected parameter.
Use to lower (decrease) the value of the selected parameter or de-select a check mark.
Use to move the cursor to left.
Use to move the cursor to right.
4. Antenna
See FCC compliance.
5. Battery Charge Outlets
The LEIT Link Remote Control Handset contains a cell battery pack that is rechargeable using the
AC/DC wall mounting battery charger 350 MA 12-volts, model 30-721. Plug the battery charger into
the LEIT Link handset for approximately 8 hours for an initial charge before using it. Then charge it
daily for a few hours as needed.
The charging screen will appear with +++C++ 4.30V within one minute after the DC
charger is plugged in. The charging screen disappears when the
button is pressed or the
charger is unplugged. A full charge will last for up to 3 hours of continuous use. The Battery Voltage
1
ABOUT THE LEIT LINK REMOTE CONTROL HANDSET
Thank you for purchasing DIG’s LEIT Link Remote Control Handset. This manual is designed to help
you get the LEIT Link handset up and running quickly. This manual will describe all you need to
know about how to use the LEIT Link handset. After you read this manual and have familiarized
yourself with the basic functionality of this device, you can use this manual as reference for less
common tasks in the future.
Models Available
• LEIT Link
®
Master
™
operates 99 groups of controllers with up to 99 controllers per each group
• LEIT Link
®
Multi-Pro
™
operates 99 controllers in one group
The LEIT Link Remote Control Handset is a 2-way radio communication device that operates in
the ISM band 902-928 MHz (868/869 Europe). The LEIT Link is a practical solution to field
communications and the management of any LEIT XRC controller in remote or hard to reach
sites.
Using the LEIT Link Remote Control Handset one can review status reports, modify program
settings, temporarily interrupt a running program to do a manual run, test a valve or skip to the next
valve mode. The current running program and current valve open information is provided when
activated. In Check Status Mode the handset also can review time, date, budget, sensor activation
(if rain sensor is active), and solenoid integrity. In Uplink History one can review the hourly usage of
each valve for all months and annual usage. Manual Run usage per month is also provided. All of
these features can be accessed from a distance of up to 800 feet line of site.
The handset can request or send information and commands to a particular controller. It will also
receive confirmation for the information sent or requested.
IMPORTANT
: The LEIT XRC requires greater energy for radio communication than is used for
operation of the controller alone. In order to retain sufficient energy to maintain valve control,
the radio on the controller will automatically turn off in low light conditions.
The LEIT XRC controller requires daily exposure to light levels at a minimum of 15.000 to 20.000
lux, which is equivalent to daylight around 9 AM-10 AM on a cloudy day. On very cloudy days
the controller requires more time to charge up and operate with the radio. To maximize the
energy available the XRC controller should be installed in an open, un-shaded area.
•
1. LCD Display
•
5. Battery
Charge Outlet
•
6. Battery
Compartment Cover
•
4. Antenna
•
2. Power
Button
•
3. Programming
Buttons
•
8. Socket Outlet
for Software
Upgrade
•
7. Battery
Socket
Outlet
•
9. Battery
Compartment
with 3 NiMH
rechargeable
AAH cells
battery pack
