background image

VECTORDRIVE DSV 5445

Top technology in drive electronics

07.07.04 10:12

 Dietz-electronic

page 36 of 60

?

{H-number} Set condition (flag checked on FFh)

!

{0..31}

Wait for conditional block invoke until condition is fulfilled

8.3  List of main memory locations

If "R" appears in the "RW" column, this means that the memory location can only be read; "RW" signifies both read
and write.
For some flags there is a corresponding counter-flag. This is set if the corresponding condition is not fulfilled.
A

 not

 is then appended to the variable name.

8.3.1 General

Address

Name

RW

Explanation

41Eh

TRUE

R

Contains the value for "true"

420h

FALSE

R

Contains the value for "false"

0F2h

FREIGABE_STB

R

FFh = control switched on

10Ch

BEREIT_MZ

R

FFh if frequency inverter not ready

EE6h

BEREIT_MZ_STB

RW

This control byte is set at 01h as standard. This means that all
faults are locked in and can only be cleared with RESET. EE6H
= 0 -> After a fault, the drive continues to operate as soon as
the fault goes (compatible with older models).

E98h

SOFTFREI

RW

In this location FFh must be input to activate the ready-for-
operation output on connector X1. This location must at any
event be set at the end of the initialization bock 16. This means
that the ready-for operation signal appears immediately after
initialization.

0FAh

ANA_SOL_STB

RW

FFh = Analog operation selected

074h

PIN_BGZ_FLAG

R

Flag is set if the setpoint torque limit is reached.

1AEh

STEHT

R

Drive stopped (N_SETPOINT_V = 0 and NS_GL_NI or
LS_GL_LI).

1AFh

STEHT

nicht

R

Counter-flag for "STOPPED"

10Eh

EK_MZ

R

FFh if earth fault or short-circuit

17Ch

ACHT_MZ

If FFh, a program run interrupt can only be cleared by pressing
the reset key or switching off the inverter.

102h

NOT_HALT_MZ

R

FFh = emergency stop triggered

094h

NOT_HALT_STB

RW

If 00h, emergency stop only reset by intermediate circuit volt-
age, "M" command or RESET, otherwise automatically when the
emergency stop has ended. With FFh, the inverter is ready for
operation again 3 seconds after the end of the emergency stop
signal (standard setting).

73Ah

ISD_SOLL

R

Longitudinal current (forming field)

73Ch

ISQ_SOLL

R

Transverse current (forming torque)

07Ah

ISQ_SOLL_MAX

R

Maximum torque (dependent on maximum possible inverter
current)

1C2h

RICHT_FLAG

R

Actual direction of rotation

116h

TEMP_FLAG

R

Temperature fault

0F2h

REG_EIN

R

This flag is set when the control is switched on.

0F3h

REG_AUS

R

This flag is set when the control is switched off

06Eh

M_SOLL_MAX

RW

Maximum motor torque specified by "S" command. The upper
limit is ISQ_SOLL_MAX. Caution: if the F0 function is invoked,
the maximum torque ("S" command) and I

2

 

×

 dt limit are set at

maximum value.

ED8h

IS_MAX

RW

Maximum torque for I

×

 dt cut-off which the motor can run con-

tinuously. Scaling corresponds to "S" command. Range: 64 -
ISQ_SOLL_MAX and can be calculated as follows: IS_MAX =
ISQ_SOLL_MAX 

×

 interior motor/l

dyn

_inverter

EE0h

IS_T

RW

Time for I

2

 

×

 dt cut-off. The motor must be able to provide dou-

ble the continuous torque IS_MAX for the time IS_T.

700h

ANA_SOLL

R

Analog setpoint value standardized with F9.

792h

ANA_OFST

RW

Hysteresis for analog specified setpoint value (5 mV/value,

Summary of Contents for DSV 5444 / ML 2





























































Reviews: