English
English
14
15
Common Power Output Problems
Problem
Possible Solution
Input voltage below
10.5 volts
Recharge auto battery or check DC power
supply.
Equipment being
operated draws too
much power
• Reduce load to maximum 1000 watts.
Inverter in thermal
shutdown condition
Allow inverter to cool down. Ensure there
is adequate ventilation around the unit and
that the load is no more than 1000 watts
for continuous operation.
AC output is
shorted
Unplug the AC appliance. Disconnect the
unit from any 12 volt DC power source.
Check the appliance cord.
Accessories
WARNING:
Since accessories, other than those offered by DeWALT,
have not been tested with this product, use of such accessories with
this unit could be hazardous. To reduce the risk of injury, only DeWALT
recommended accessories should be used with this product.
If you need assistance regarding accessories, please contact the
manufacturer at 1-888-394-3392 or CustomerService@dewalt12volt.
com.
Service Information
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the manufacturer at 1-888-394-3392 or
One Year Limited Warranty
The warranty of this product is covered by Baccus Global LLC
(1-888-394-3392 or [email protected]). The
manufacturer warrants this product against defects in material and
workmanship for a period of one (1) year from the date of retail purchase
by the original end-user purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty
Period, the defective product can be repaired, replaced or refunded,
without charge, in the following ways: (1) Return the product to the
manufacturer for repair, replacement or refund at manufacturer’s option.
Proof of purchase may be required by manufacturer. (2) Return the
product to the retailer where product was purchased for an exchange
(provided that the store is a participating retailer). Returns to retailer
should be made within the time period of the retailer’s return policy for
exchanges only (usually 30 to 90 days after the sale). Proof of purchase
may be required. Please check with the retailer for their specific return
policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to: accessories, bulbs, fuses and
batteries; defects resulting from normal wear and tear, accidents;
damages sustained during shipping; alterations; unauthorized use or
repair; neglect, misuse, abuse; and failure to follow instructions for care
and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal
rights and you may have other rights which vary in certain states or
provinces. This product is not intended for commercial use.
90 DAY REFUND POLICY
If you are not completely satisfied with the performance of this product
for any reason, you can return it within ninety (90) days from the date
of purchase with a receipt for a full refund.
Please complete the Product Registration Card and return within
30 days from purchase of the product to: Baccus Global LLC,
Specific USB Power Port Problems
When the USB ports are in use, the unit will monitor for the following
USB fault conditions on all the USB ports: thermal fault, low battery
voltage fault, overload and short circuit.
Problem
Possible Solution
If a fault condition exists
in either of the USB
ports, the LCD will
display the USB fault
condition and the USB
power/fault indicators
shut off. In any of these
cases, the USB ports will
automatically shut down.
Should this occur:
A. Disconnect the USB-powered
device and press the power
button again to turn off the unit
immediately.
B. Allow the unit to cool down for
several minutes before attempting
to use the USB ports again.
C. If a fault occurs again, make sure
that the total draw of all USB
devices plugged into the USB
ports does not exceed 3.1A.
D. If an individual USB device is
within specifications and the fault
occurs, have the USB device
checked for malfunction and do
not continue to use it with these
USB ports.
Common Audio Problems
Problem
Possible Solution
Buzzing Sound In
Audio Systems
Some inexpensive stereo systems and
boom boxes make a buzzing sound
when operated from the inverter,
because the power supply in the
electronic device does not properly filter
the modified sine wave produced by the
inverter. The only solution to this problem
is to use a sound system that has a
higher quality power supply.
Television
Interference
The inverter is shielded to minimize
interference with TV signals. However,
in some instances, some interference
may still be visible, especially when the
TV signal is weak. Try the following to
improve the picture:
1. Move the inverter as far away
as possible from the TV set, the
antenna, and the antenna cables.
Use a short AC extension cord, if
necessary.
2. Adjust the orientation of the antenna
cables, and the TV power cord to
minimize interference.
3. Make sure that the antenna feeding
the TV provides an adequate (snow-
free) signal and that high quality,
shielded antenna cable is used.
DXAEPI1000_ManualENSP_080320.indd 14-15
DXAEPI1000_ManualENSP_080320.indd 14-15
8/3/2020 1:40:38 PM
8/3/2020 1:40:38 PM
