Develco MOSZB-130 Technical Manual Download Page 21

Page: 21 / 28

Motion Sensor - MOSZB-130 – Technical manual

Develco Products A/S

Olof Palmes Allé 40

http://develcoproducts.com

DK-8200 Aarhus N

[email protected]

4.4

Temperature Sensor Device – EP 0x26

4.4.1

Temperature Measurement – Cluster id 0x0402

The temperature measurement cluster is described in ZigBee Cluster Library Specification section 4.4

4.4.1.1

Attribute

Id#

Name

Type

Range

Man/Opt

Relevance and ref.

0x0000

MeasuredValue

Sint16

MinValue to

MaxValue

ZCL Reporting is support

DP default is configured

0x0001

MinMeasuredValue

Sint16

0x0002

MaxMeasuredValue

Sint16

5000

4.4.1.1.1

MeasuredValue

The attribute is configured with the following default “ZCL configure reporting” setting.



Min Reporting Interval: 0x003C [60 sec]



Max Reporting Interval: 0x0258 [600 sec]



Reportable Change: 0x000A [0.1 °C]

If the temperature value is stable it will be send every 10 minutes.

If  the  temperature  changes  more  than  0.1  °C  it  will  be  reported  but  not  faster  than  every  1  minute  since  last
reporting value.
Note: Min reporting interval 0 sec is invalid when reportable change is configured.

4.4.1.1.2

MinMeasuredValue

The temperature sensor is NOT supporting temperature measurements below 0 degrees Celsius.

Summary of Contents for MOSZB-130





























Search results

Summary of Contents for MOSZB-130

Reviews:

Related manuals for MOSZB-130

Brands by name

Popular brands

Develco MOSZB-130, Technical Manual

Search results

Summary of Contents for MOSZB-130

Reviews:

Related manuals for MOSZB-130

Brands by name

Popular brands