background image

It is the responsibility of the receiver of the goods, either the Distributor or Customer, to ensure that the 
product has been shipped in full, and has arrived in suitable condition. Damage to the product may not be 
visible at time of off-loading, but may only become apparent upon unpacking or start-up.

Some areas to initially check are as follows:

a) Check for damage to the Belt Guard.
b) If the Belt Guard appears damaged, remove the Guard and turn the Flywheel by 

hand to ensure the Crankshaft has not been bent, and that the Belt Drive is properly 
aligned and free of distortion.

c) Check the Air Tank and attached Legs for possible damage.

Should there be shortages in shipment or damage to the product:

1) Stop any further unpacking or operation of the product.
2) Make  note  of  the  problem  on  the  Freight  Bill,  should  it  concern  a  shortage  or  visible 

damage to the product.

3) Should  the  damage  be  noticed  only  after  the  product  has  been  received,  contact  the 

transport company immediately to file a claim.
Depending  on  the  problem,  it  may  be  wise  to  photograph  the  damage.  Also,  it  may 
be  wise  to  discuss  with  the  carrier  representative  the  time  allotted  to  give  notice  of  loss 
or damage to the product; there may be guidelines which limit time-frames of same.

4) Do  not  attempt  further  unpacking  or  operation  of  the  product.  Also,  do  not  discard 

any packing material used.

5) A  Loss  or  Damage  Claim  must  be  submitted  to  the  carrier  and  supported  by  the 

following documents:
- Copy of Freight Bill of Lading
- Copy of the Invoice and Estimate to repair, in case of damage
- Damage Report
- Copy of photos, if applicable

Unpacking and Inspection

Each  Devair  ‘HDI’  Air  Compressor  is  carefully  tested  and  inspected  before 
shipment.  Though  every  attempt  is  made  to  ensure  the  safe  and  complete 
shipment of our product, freight damage or misplacement of goods may occur.

Shipments  of  Devair  products  are  the  property  of  the  Consignee  when  the 
products leave our facility. Devair Inc. is not responsible for any damages or 
shortages caused to the product after it has left our shipping dock.

NOTE

 - 5 -

HDI-01

Mar ‘07

Distributed by:     CENTRAIR Air Systems & Supplies,    68 Hooper Rd., Unit 5, Barrie, ON  L4N 8Z9

                               Phone: 705-722-5747  Fax: 705-722-5458     [email protected]    www.centrair.ca

All manuals and user guides at all-guides.com

Summary of Contents for HDI-01

























Reviews: