manualshive.com logo in svg

Devair HDI-01, Installation Maintenance And Service Manual

Share
Download
Devair HDI-01 Installation Maintenance And Service Manual Download Page 10

Fill the Crankcase to the lowest thread at the Oil 

Fill  Port  Opening. 

Do  not  under  or

 

overfill.

 

See drawing below.

Always  replace  the  O-Ring  when  filling,  and 

tightly  screw  in  Oil  Fill  Plug  using  a  crescent 
w r e n c h . U s e   o n l y  

D e v a i r   P r e m i u m  

Compressor Oil

 

 

for the Air Compressor, as it 

has been specially formulated for your Unit, and 
contains only two additives, a rust inhibitor and 
an anti foaming agent.

The  following  Maintenance  Kits  are  available 

through  your  Devair  Distributor,  the  Kits 
including Devair Premium Oil and Air Filter (s).

Do not attempt to operate the Unit without 
first checking whether there is Oil in the 
Pump.  Add  Oil  as  required.  Serious 
damage  may  result  from  use,  however 
limited, without Oil.

Use of improper Oil may negatively a f f e c t  
Compressor  Pump  performance  or 
shorten Pump life. Resulting problems are 
not  covered  by  the  Devair  Inc.  Air 
Compressor  Warranty. 

Pump Lubrication

 - 10 -

Devair Premium
Mineral Oils

Devair Pump Model

Devair Pump Model

Devair Premium Synthetic Oil

 (used in 

high heat or high duty applications or 
when Beltguard Aftercoolers are used)

DV Lube20 (20 Wgt)
Part No. ‘PR20’

DV Lube30 (30 Wgt)
Part No. ‘PR30’

123

247

44642

OJ-2000 (20 Weight)

223

447

247

447

Up to 90°F (32°C)

MK-223

MKS-247

MK-247

90°F + (32°C +)

MK-223

MKS-447

MK-247

MK-447

Room (Ambient)
Temperature

Kit Part Number

Kit Part Number

'O' Ring

Proper Oil Level

(to bottom thread of Oil Port)

Oil Filler

Plug

Section Through CrankCase

at Oil Fill Port

Kits c/w Mineral Oil (20 Weight only)

Kits c/w Synthetic Oil

HDI-01

Mar ‘07

Distributed by:     CENTRAIR Air Systems & Supplies,    68 Hooper Rd., Unit 5, Barrie, ON  L4N 8Z9

                               Phone: 705-722-5747  Fax: 705-722-5458     [email protected]    www.centrair.ca

All manuals and user guides at all-guides.com

Summary of Contents for HDI-01

























Reviews:

No comments

Brands by name

Popular brands

Load more brands