manualshive.com logo in svg

Devair HDI-01, Installation Maintenance And Service Manual

Share
Download
Devair HDI-01 Installation Maintenance And Service Manual Download Page 2

The following hazards may occur during the normal use of the equipment. Please 
read the following chart.

In order to operate the Compressor Unit safely and correctly, we have opted to use the following symbols to make you 

aware of important points. These points relate to user safety and preventing equipment problems. Please pay close 
attention to these sections.

Tampering  with  the  Unit  while  under  full  or  partial 
pressure may cause an explosion.

Relieve all pressure from the Unit before attempting 
any repair or maintenance work.

As  the  Unit  starts  and  stops  automatically  ,  serious 
injury may result from working on the Compressor with 
the power still in the on position.

Shut off all power to the Unit before attempting to 
repair or maintain the Compressor.

What to look for.

How to avoid the hazard

What may occur if precautions are not 
observed.

Area:

Hazard:

Safeguards:

Important  safety  information.  A 
hazard  that  may  cause  serious 
injury or loss of life.

Important information that indicates 
how  to  prevent  damage  to 
equipment,  or  to  avoid  a  situation 
that may cause minor injury.

Information  that  you  should  pay 
special attention to.

NOTE

 - 2 -

Safety Precautions

As the Unit starts and stops automatically, do not come 
into contact with moving parts.

Shut off all power to the Unit before attempting to 
repair or maintain the Compressor.

Air compressed by the Unit is not suitable for inhaling. It 
may contain poisonous vapours harmful to your health.

Never directly inhale compressed air produced by 
the Compressor.

Compressor Air End, Motor, and Tubing become hot 
when  running.  Touching  these  areas  may  cause 
severe burns.

Never touch the Air End, Motor, or Tubing during or 
immediately after operation.

As the electrical compo-nents on the Compressor are 
General  Purpose  and  the  Motor  is  Totally  Enclosed 
(TEFC),  there  is  a  potential  for  explosion,  should 
vapours be present in the area.

The Compressor must be a minimum of 20 Feet (6.1 
Metres)  from  any  source  of  potentially    explosive 
vapours.

20FT

6.1m

HDI-01

Mar ‘07

Distributed by:     CENTRAIR Air Systems & Supplies,    68 Hooper Rd., Unit 5, Barrie, ON  L4N 8Z9

                               Phone: 705-722-5747  Fax: 705-722-5458     [email protected]    www.centrair.ca

All manuals and user guides at all-guides.com

Summary of Contents for HDI-01

























Reviews:

No comments

Brands by name

Popular brands

Load more brands