manualshive.com logo in svg

Deteck Edge DT800, Manual Instructions, Page: 23 / 25

Share
Download
Deteck Edge DT800 Manual Instructions Download Page 23

2

Ġ

code

YMaa/?oa

possible cause

E

F0

2

SOLENOID NOT IN RIGHT 

POSITION

 

•

Remove the notes from the reject pocket and 
clean the sensors

•

If the error persists, please contact the support 
team

E

F0

3

NOTES STUCK

E

F13

•

Pull out the bottom drawer and remove the 
stuck notes

E

F

0

4

NOTES STUCK

 

NOTES STUCK

•

Open the Upper compartment and remove the 
stuck notes 

EF05

NOTES STUCK

MOTOR ERROR

 

HOPPER ERROR

•

Remove the notes from the stacker 

EF06

BACK COVER ERROR

•

Remove the notes from the reject pocket

 

E

F0

1

REJECT POCKET IS FULL

•

Remove the notes from the reject pocket

Maintenance and troubleshooting

CAUTION: 

Please ensure 

the device is 

turned off before opening the upper 

compartment and bottom drawer.

EF14

EF10

EF11

EF12

•

Check all the compartments and remove any 
stuck notes 

•

Restart the machine

•

Open the Upper compartment and remove the 
stuck notes

•

Open the Upper compartment and remove the 
stuck notes

Summary of Contents for Edge DT800


























Reviews:

No comments