background image

EN

Product Information

06/2020

3 / 24

Product Information

General Information

WARNING Risk of Property Damage or Severe Injury

Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the
instructions may result in electric shock, fire, property damage and/or severe bodily injury.

Read all Safety Information delivered together with the different parts of the system.

Read all Product Instructions for installation, operation and maintenance of the different parts of the system.

Read all locally legislated safety regulations regarding the system and parts thereof.

Save all Safety Information and instructions for future reference.

Warranty

• Product warranty will expire 12 months after the product is first taken into use, but will in any case expire at the

latest 13 months after delivery.

• Normal wear and tear on parts is not included within the warranty.

• Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools

maintenance typical for that period (expressed in time, operation hours or otherwise).

• The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.

• Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Desoutter

or their Certified Service Partners during the warranty period is not covered by the warranty.

• To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance sched-

ules and follow the correct instructions.

• Warranty repairs are only performed in Desoutter workshops or by Certified Service Partners.

Desoutter offers extended warranty and state of the art preventive maintenance through its Tool Care contracts. For
further information contact your local Service representative.

For electrical motors:

• Warranty will only apply when the electric motor has not been opened.

Website

Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Desoutter
website.

Please visit: 

www.desouttertools.com

.

Information about spare parts

Exploded views and spare parts lists are available in Service Link at 

www.desouttertools.com

.

Dimensions (mm)

L

ØA

ØB

ØC

EABx 15-900

470

46

46

37

EABx 26-560

496

46

46

37

EABx 32-410

496

46

46

37

EABx 45-330

506

46

46

37

Summary of Contents for 6151659610

























Reviews: