background image

www.desatech.com

119426-01F

4

SAFETy INFORMATION

Continued

1.  This appliance is only for use with the type 

of gas indicated on the rating plate. This 
appliance is not convertible for use with 
other gases.

2.  Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply 
tank(s) outdoors (propane/LP units only).

3.  If you smell gas

• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not 

use any phone in your building

• immediately call your gas supplier from 

a  neighbor’s  phone.  Follow  the  gas 
supplier’s instructions

• if  you  cannot  reach  your  gas  supplier, 

call the fire department

4.  This heater shall not be installed in a bed-

room or bathroom, unless installed as a 

vented appliance. See 

Installing Damper 

Clamp Accessory for Vented Operation

page  12  (Remote-Ready  Models  Only). 
This  gas  log  set  may  not  be  installed 
as  a  vented  appliance  in  a  bedroom  or 
bathroom in the Commonwealth of Mas-
sachusetts.

5.  Before installing in a solid fuel burning fire

-

place, the chimney flue and firebox must 
be cleaned of soot, creosote, ashes and 
loose paint by a qualified chimney cleaner. 

Creosote will ignite if highly heated. A dirty 

chimney  flue  may  create  and  distribute 

soot  within  the  house.  Inspect  chimney 

flue for damage. If damaged, repair flue 
and firebox before operating heater.

6.  Do  not  burn  solid-fuel  in  a  masonry  or 

UL127  factory-built  fireplace  in  which  a 

vent-free room heater is installed.

7.  If fireplace has glass doors, never operate 

this heater with glass doors closed. If you 

operate  heater  with  doors  closed,  heat 
buildup inside fireplace will cause glass to 

burst. Make sure there are no obstructions 

across openings of fireplace.

8.  To prevent the creation of soot, follow the 

instructions in 

Cleaning and Maintenance

page 26.

9.  Before using furniture polish, wax, carpet 

cleaner or similar products, turn heater off. If 
heated, the vapors from these products may 

create a white powder residue within burner 
box or on adjacent walls and furniture.

10. This heater needs fresh, outside air ven

-

tilation to run properly. This heater has an 
Oxygen Depletion Sensing (ODS) safety 
shutoff system. The ODS shuts down the 
heater if enough fresh air is not available. 

See 

Air for Combustion and Ventilation

page 6. If heater keeps shutting off, see 

Troubleshooting

, page 28.

11. Do not run heater

• where flammable liquids or vapors are 

used or stored

• under dusty conditions

12. Do not use this heater to cook food or burn 

paper or other objects.

13. Do not use heater if any part has been ex-

posed to or under water. Immediately call 

a qualified service technician to inspect 

the room heater and to replace any part 
of the control system and any gas control 
which has been under water.

14. Do not operate heater if any log is broken. 

Do not operate heater if a log is chipped 

(dime-sized or larger).

15. Turn  heater  off  and  let  cool  before  ser-

vicing, installing or repairing. Make sure 

the selector switch is in the OFF position 
(Remote-Ready  Models  Only).  Only  a 

qualified  service  person  should  install, 

service or repair heater.

16. Make  sure  the  selector  switch  is  in  the 

OFF  position  when  you  are  away  from 
home for long periods of time (Remote-
Ready Models Only).

17. Remote-ready heaters must not be con-

nected to any external electrical source.

18. Operating  heater  above  elevations  of 

4,500 feet may cause pilot outage.

19. To prevent performance problems, do not 

use propane/LP fuel tank of less than 100 
lb. capacity (propane/LP units only).

20. Provide adequate clearances around air 

openings.

UNPACkING

 CAUTION: Do not remove the 

data  plates  from  the  grate  as-

sembly. The data plates contain 

important  warranty  and  safety 

information.

1.  Remove logs and heater base assembly 

from carton. 

Note: 

Do not pick up heater 

base  assembly  by  burners.  This  could 
damage heater. Always handle base as-
sembly by grate. 

2.  Remove all protective packaging applied 

to logs and heater for shipment.

3.  Check all items for any shipping damage. 

If damaged, promptly inform dealer where 

you bought heater.

Summary of Contents for VUL18NR













































Reviews: