background image

www.desatech.com

119426-01F

17

INSTALLATION

Continued

INSTALLING OPTIONAL REMOTE 
ACCESSORIES

Installing Remote Receiver 

Remote  control  accessories  are  available 
separately (see 

Accessories

, page 41).

1.  If unit is already installed in fireplace, con

-

tinue with these instructions. If unit has not 

been installed in fireplace, go to step 6 and 

continue installation of remote accessory.

  WARNING:  Turn  off  heater 

and let cool before handling any 

part of heater. Make sure gas is 

turned of to unit.

2.  Carefully remove logs and set aside.
3.  Locate mounting screws on sides of heat-

er base assembly and remove screws. Set 
screws aside for reinstallation.

4.  Disconnect gas line from heater base as 

shown in Figure 11 or 12, page 13.

 WARNING: A qualified ser-

vice person must connect and 

disconnect gas to heater. Follow 

all local codes.

5.  Remove heater base from fireplace.

6.  Install receiver bracket to base with Phil-

lips  screws  provided  in  hardware  kit  as 
shown in Figure 20.

7.  Disconnect jumper wire from control valve at 

TPTH and TH locations (see Figure 21).

8.  Install  remote  receiver  into  receiver 

bracket using pads and push button clips 
provided with receiver (see Figure 22).

9.  Connect  wires  to  control  valve  at  the 

TPTH  and  TH  locations  as  shown  in 
Figure 23. 

Note: 

Make sure excess wire 

does not interfere with burner or pilot.

10. If heater was removed from fireplace be

-

fore installation of remote accessory, see 

Installing Heater Base Assembly

 on page 

12 to reinstall heater into fireplace. Test 

gas connection for leaks (see 

Checking 

Gas Connections

, page 15).

11. If logs were removed from heater for in-

stall remote accessory, replace logs (see 

Installing Logs

, page 18).

Figure 22 - Installing Remote Receiver

Push 
Button 
Clips

Bracket

Battery 
Clip

9-Volt Battery

Terminal 
Wires

Pad

Figure 21 - Disconnecting Jumper Wire 

From Control Valve

Jumper 
Wire

Control Valve

Figure 20 - Installing Remote Receiver 

Bracket

Remote Receiver Bracket

Phillips 
Screws

Figure 23 - Connecting Wires

Control Valve

White Wire 
From Receiver

Red Wire From 
Receiver

Summary of Contents for VUL18NR













































Reviews: