manualshive.com logo in svg

Chiltrix V18-B, Installation And Operation Manual

Share
Download
Chiltrix V18-B Installation And Operation Manual Download Page 1

V18-B Installation and 
Operation Manual 

Thank you for purchasing the worlds most advanced and efficient hydronic backup heating solution for air-to-water heat 
pumps. The V18 adds backup heat in more precise amount, with variable & automatic real time control. For use with 
Chiltrix air-to-water heat pumps. 

 The new B-Model uses the Chiltrix CX34 onboard controls and does not need a 
separate V18 controller, requires CX34 firmware P228-S10-V200B26 or later, it 
generally applies to all CX34 units produced after November 2019. Some older 
units also have this firmware version but it must be verified. 

WARNING!

 

THIS PRODUCT USES HIGH VOLTAGE ELECTRICITY!

 

DO NOT OPEN OR SERVICE THIS DEVICE UNLESS POWER HAS BEEN 
DISCONNECTED

 

This product must be assembled and installed by a licensed electrician in 
a manner that conforms with all national and local electrical and safety 
codes. All high voltage electrical components meet UL requirements. 

SERVICE OR REPAIR TO BE PERFORMED ONLY BY A LICENSED ELECTRICIAN

 

DO NOT DRY FIRE THIS DEVICE / INSTALL VERTICALLY ONLY

 

USE 208-240V 30a Circuit with GFCI Breaker.

 

Note special procedure for chilled water capable systems. 

Read the entire manual before beginning installation. 

Follow all instructions. 

 

Version 1.0 

1 

Summary of Contents for V18-B




















Reviews:

No comments

Brands by name

Popular brands

Load more brands