manualshive.com logo in svg

Chiltrix V18-B, Installation And Operation Manual

Share
Download
Chiltrix V18-B Installation And Operation Manual Download Page 19

 

 

 

NOTICE  

 

Bulletin Regarding V18 Installed 

With CX34 Systems Used For Cooling

 

 

 

CHILLED WATER

 

 

IMPORTANT NOTE* 

 
If the V18 will be installed in a system that performs cooling operation at 
times, make sure to thoroughly seal around the white ABS cover and 
inside the Liquidtight conduit with silicone as a minimum precaution. 
 

Make sure power is disconnected before and during this operation. 

 
The requirement is to prevent air from entering the V18 inside the white 
ABS cover and contacting the cold pipe or components which could cause 
condensation to form and accumulate inside the unit.  
 
For high humidity locations you may also consider filling the entire cavity 
(but not cover the reset button) with an  electronics-grade silicone potting 
material rated for this type of application. Example: GC 19-160 or similar. 
(gcelectronics.com) 
 

Make sure power is disconnected before and during this operation. 

 
When using a silicone potting material, use it only per-code and according 
to the material manufacturers instructions and make sure to allow the 
material to fully cure before attaching the cover. Do not cover the reset 
button with silicone. 
 

Do not connect power until the material has fully cured and white cover 
has been replaced. 

 
 
 

19 

Summary of Contents for V18-B




















Reviews:

No comments

Brands by name

Popular brands

Load more brands