background image

5

106706

OWNER’S MANUAL

For more information, visit www.desatech.com

STOVE BODY ASSEMBLY

1.

Lift off corrugated box enclosing stove
body crating.

2.

Remove all screws fastening the wood
frame enclosure. Spread wood frame open
and lift away from plastic-bagged stove
body. The bottom pieces of pallet wood
will remain bolted to the stove body.

3.

Remove plastic bag from stove body.

4.

Remove back panel from stove and dis-
card (see Figure 6). Use an adjustable
wrench or a 10 mm socket. Remove six
(6) bolts and washers. Keep bolts and
washers to attach rear cover.

5.

Remove all contents from inside stove
cavity. Contents include:
(1) - Stove bottom (Discard - Not used

with this application)

(4) - Legs with leg leveler bolts
(1) - Bottom door
(3) - Top grates
(1) - Hardware kit bag with fasteners

6.

Carefully lay stove body on back to at-
tach bottom components to stove body
(see Figure 7). Rest stove on drop cloth
or blanket to avoid scratching stove edges.

7.

Remove remaining pallet wood at-
tached to bottom of stove body (see
Figure 8). Use an adjustable wrench to
remove bolts.

8.

Fasten each leg to stove with four (4)
M8 x 1.25 - 20mm bolts. Use a flat
washer and lock washer with each bolt.
Tighten bolts into threaded holes on
stove body (see Figure 9 and Figure 10,
page 6). Use an adjustable wrench or a
12mm socket.

Figure 7 - Laying Down Stove On Side

Figure 6 - Removing Back Panel

CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
ASSEMBLY

Continued

Bolt

Product
Identification
Label

Back
Stove
Panel

Pallet
Wood
Bolted to
Bottom of
Stove Body

Front of
Stove Unit

Top of Stove Unit

Front of Stove Unit

 Stove
Unit

Drop
Cloth/
Blanket

Figure 8 - Removing Pallet Wood From The Bottom of The Stove

Pallet Wood

Bolt

Pallet Wood

Bottom Of
Stove Unit

Front

Figure 9 - Locating Threaded Holes for Legs and Door Attachment

Door Hinge
Step Bolt Hole

Door Catch Bolt With
Adjustable Hex Nuts Hole

Leg
Hole

Leg Hole

Leg
Hole

Front

Bottom Of
Stove Unit

Summary of Contents for MSRBVN

































Reviews: