background image

www.desatech.com

123167-01D

18

INSTALLATION

Continued

Figure 22 - Installing Front Log 

Front Log

Grate

3.  Place front log (#3) onto grate as shown 

in Figure 22.

4.  Place left top log (#4) as shown in Figure 

23. Match square peg on top of rear log 

(#1) with square hole on bottom of left top 

log (#4). Match round peg on top of middle 

log (#2) with round hole on bottom of left 

top log (#4).

5.  Place right top log (#5) as shown in Figure 

23. Match square peg on top of rear log 

(#1) with square hole on bottom of right 

top log (#5). Match round peg on top of 

front log (#3) with round hole on bottom 

of right top log (#5).

Figure 23 - Installing Left and Right Logs 

Left Top 
Log

Square Peg 
on Rear Log

OPERATION

FOR YOUR SAFETY  

READ BEFORE LIGHTING

 WARNING: If you do not fol-

low  these  instructions  exactly, 

a  fire  or  explosion  may  result 

causing property damage, per

-

sonal injury or loss of life.

A.  This appliance has a pilot which must 

be  lighted  by  hand.  When  lighting 
the  pilot,  follow  these  instructions 
exactly.

B.  BEFORE  LIGHTING  smell  all  around 

the appliance area for gas. Be sure to 
smell next to the floor because some 
gas is heavier than air and will settle 
on the floor.

 

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electric switch; do 

not use any phone in your building.

• Immediately  call  your  gas  supplier 

from a neighbor’s phone. Follow the 
gas supplier’s instructions.

• If you cannot reach your gas supplier, 

call the fire department.

C.  Use only your hand to push in or turn 

the gas control knob. Never use tools. 
If the knob will not push in or turn by 
hand, don’t try to repair it, call a quali

-

fied service technician or gas supplier. 
Force or attempted repair may result in 
a fire or explosion.

D.  Do  not  use  this  appliance  if  any  part 

has been under water. Immediately call 
a qualified service technician to inspect 
the appliance and to replace any part of 
the control system and any gas control 
which has been under water.

Round 
Peg on 
Middle 
Log

Right 
Top 
Log

Round 
Peg on 
Front Log

Summary of Contents for HD18NRA

































Reviews: