background image

Model Number

MH-400T-KFA

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

GENERAL HAZARD WARNING: 

Be sure to comply with the 

instructions and warnings provided with this heater, or death, 

serious bodily injury and property loss, damage from the hazards 

of fire, explosion, burn,asphyxiation, and carbon monoxide poisoning can result.

Only persons who can follow and understand these instructions should use or service this 

heater. If you need heater information such as an instruction manual, labels, etcetera, 

contact the manufacturer.

DANGER

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (800) 779-3267

Fax: 320-251-2922 • Web: www.masterindustrialproducts.com • Email: [email protected]

© 2017 Pinnacle Climate Technologies, Inc. MAKB-409

User’s Manual & 

Operating Instructions

KEROSENE FORCED AIR 

HEATER

IMPORTANT: 

Read and understand all of the directions in this manual before assembling, 

starting, or servicing the heater. Improper use of this heater can cause serious injury. Keep 

this manual for future reference. The requirements of local authorities having jurisdiction 

shall be followed.

Not for use in residential living areas or in non-adequately ventilated 

enclosed spaces. For outdoor use. Indoor use permitted for: The 

temporary heating of adequately ventilated buildings or structures 

under construction, alteration or repair.

DANGER

Summary of Contents for MH-400T-KFA
















Reviews: