Dentsply Sirona Primeprint Instructions For Use Manual Download Page 35 | Manualshive

Page: 35 / 51

Dentsply Sirona Primeprint Instructions For Use Manual Download Page 35

Dentsply Sirona
Instructions for Use Primeprint

5 Commissioning

5.1 Putting the inLab 4 PC into operation

67 45 173 D3691
D3691.201.01.01.02 04.2021

35

5.1.1.2

Making connections

NOTE

Do not connect and turn on the device yet!

First, connect the PC to the monitor, keyboard, and mouse.

Follow the instructions in this document exactly in order to
successfully perform start-up of your device.

You must install the user software prior to connecting the device to
the PC.

G

F

C

B

A

D

E

A

USB license stick

B

USB port

C

Keyboard/mouse

Alternatively: Connection via USB

D

USB connections

E

Ethernet connection

F

Optional: Audio output

G

Monitor

1.

Connect the keyboard and the mouse to the PC.

2.

Connect the monitor to the PC with the VGA/DVI cable.

3.

Connect the Ethernet port on your device to the Ethernet port on
your PC.

4.

Turn on the monitor and PC power supplies.

5.

Turn on the power switch on the rear panel of the PC (if present).

«
...
33
34
35
36
37
...
»

Summary of Contents for Primeprint




















































Reviews:

No comments