Dentsply Sirona Primeprint Instructions For Use Manual Download Page 10 | Manualshive

Page: 10 / 51

Dentsply Sirona Primeprint Instructions For Use Manual Download Page 10

1 General data
1.7 Legend

Dentsply Sirona

Instructions for Use Primeprint

10

67 45 173 D3691

D3691.201.01.01.02 04.2021

1.7

Legend

20XX

Year of manufacture

Product disposal symbol (see "Disposal [→ 66]").

Accompanying documents

This symbol can be found on the rating plate on the unit.

Meaning: Observe the Operating Instructions when operating the unit.

This symbol can be found on the rating plate on the unit.

Meaning: The accompanying documents are available on the Dentsply
Sirona homepage.

Electrostatic discharge (ESD)

Connector pins or sockets bearing ESD warning labels must not be
touched or interconnected without ESD protective measures. See also
"Electrostatic charge [→ 17]" and "Electromagnetic compatibility".

Disconnection of the power supply during
maintenance work

If the device-sided electronics box must be opened during maintenance
work, this may be done only after disconnection of the power supply to
the device.

General danger notice

Observe the Operating Instructions.

Wear protective gloves.

"Hot surface" symbol

«
...
8
9
10
11
12
...
»

Summary of Contents for Primeprint




















































Reviews:

No comments