Dentsply Sirona Primeprint Instructions For Use Manual Download Page 31 | Manualshive

Page: 31 / 51

Dentsply Sirona Primeprint Instructions For Use Manual Download Page 31

Dentsply Sirona
Instructions for Use Primeprint

4 Transportation and installation

4.3 Installation requirements

67 45 173 D3691
D3691.201.01.01.02 04.2021

31

4.3

Installation requirements

4.3.1

Requirements on the place of installation

Make sure that the unit is installed on an even, horizontal surface of
approx. 530x515 mm (W x D). The load carrying capacity should be at
least 50 kg. The height of the machine is 670 mm.

Install the machine so that access to the power plug is guaranteed at all
times. Make sure that the ventilation slots on the rear of the unit remain
unobstructed.

The distance between the back of the unit and the wall must be at least
5 cm.

Note the weight of 41 kg!

The unit must not be installed at sites with a high level of humidity or
dust!

4.3.2

Requirements for the storage of the material units

At least one Primeprint material unit and one Primeprint box is required
to operate the 3D printer. Please observe the following instructions
regarding storage.

For storage, observe the requirements of the material manufacturer.

«
...
29
30
31
32
33
...
»

Summary of Contents for Primeprint




















































Reviews:

No comments