manualshive.com logo in svg

Dentsply Sirona Primeprint, Instructions For Use Manual, Page: 30 / 51

Share
Download
Dentsply Sirona Primeprint Instructions For Use Manual Download Page 30

4 Transportation and installation
4.1 unpacking

Dentsply Sirona

Instructions for Use Primeprint

30

67 45 173 D3691

D3691.201.01.01.02    04.2021

4

Transportation and installation

4.1

unpacking

All products from Dentsply Sirona are carefully checked prior to
shipment. Please perform an incoming inspection immediately after
delivery.

1.

Check the delivery note to ensure that the consignment is complete.

2.

Check whether the product shows any visible signs of damage.

NOTE

Damage during transport

If the product was damaged during transport, please contact your
carrying agent.

If return shipment is required, please use the original packaging for
shipment.

Transportation without packaging

CAUTION

Damage to the unit or risk of injury during transport without packaging

There is a danger of the unit falling down if it is grasped by its plastic
housing.
➢ The unit should always be carried by two persons.
➢ Do not grasp the unit by its plastic housing.
➢ Always grasp the unit by the base of the unit next to its feet.

4.2

Disposal of packaging materials

The packaging must be disposed of in compliance with the relevant
national regulations. Please observe the regulations applicable in your
country.

Summary of Contents for Primeprint




















































Reviews:

No comments