76
ENGLISH
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
Manual Setup
Setting items
Setting details
Speaker Config.
(Continued)
F.Wide
: Set the presence and size of the front wide speakers.
•
Large
: Use a large speaker that can adequately play back low
frequencies.
•
Small
: Use a small speaker that has inadequate playback capacity for
low frequencies.
•
None
: Select when the front wide speakers are not connected.
NOTE
When “Amp Assign” setting (
v
page 75) is other than “Normal”, you
cannot make the “F.Wide” setting.
Bass Setting
Set subwoofer and LFE
signal range playback.
Subwoofer Mode
: Select low range signals to be reproduced by
subwoofer.
•
LFE
: The low range signal of the channel set to “Small” speaker size is
added to the LFE signal output from the subwoofer.
•
LFE+Main
: The low range signal of all channels is added to the LFE
signal output from the subwoofer.
• “Subwoofer Mode” can be set when “Speaker Config.” – “Subwoofer”
(
v
page 75) is set to “Yes”.
• Play music or a movie source and select the mode offering the strongest
bass.
• Select “LFE+Main” if you want the bass signals to always be produced
from the subwoofer.
NOTE
If “Front” and “Center” for “Speaker Config.” are set to “Large”, and
“Subwoofer Mode” is set to “LFE”, no sound may be output from the
subwoofers, depending on the input signal or selected surround mode.
LPF for LFE
: Set LFE signal playback range.
•
80Hz
/
90Hz
/
100Hz
/
110Hz
/
120Hz
/
150Hz
/
200Hz
/
250Hz
Distance
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
Unit
: Set the unit of distance.
•
Meters
/
Feet
Step
: Set the minimum variable width of the distance.
•
0.1m
/
0.01m
•
1ft
/
0.1ft
Front L
/
Front R
/
Center
/
Subwoofer
/
Surround L
/
Surround R
/
S.Back L
z
/
S.Back R
z
/
F.Height L
/
F.Height R
/
F.Wide L
/
F.Wide R
: Select the speaker.
z
When the “Speaker Config.” – “S.Back” setting (
v
page 75) is set to
“1spkr”, “S.Back” is displayed.
•
0.00m
–
18.00m
/
0.0ft
–
60.0ft
: Set the distance.
Setting items
Setting details
Distance
(Continued)
• The speakers that can be selected differ depending on the “Amp Assign”
(
v
page 75) and “Speaker Config.” (
v
page 75) settings.
• Default settings :
Front L / Front R / Center / Subwoofer / F.Height L / F.Height R / F.Wide L /
F.Wide R : 3.6 m (12.0 ft)
Surround L / Surround R / S.Back L / S.Back R : 3.0 m (10.0 ft)
• Set the difference in the distance between the speakers to less than
6.0 m (20 ft).
NOTE
Speakers set to “None” in “Speaker Config.” (
v
page 75) are not displayed.
Default
: The “Distance” settings are returned to the default settings.
•
Yes
: Reset to the defaults.
•
No
: Do not reset to the defaults.
When you select “Default” and press
ENTER
, the “Default Setting?”
prompt is displayed. Select either “Yes” or “No”, and press
ENTER
.
Channel Level
Set the volume of the test
tone to be the same when it
is output from each speaker.
Test Tone Start
: Output test tone.
•
Front L
/
F.Height L
/
Center
/
F.Height R
/
Front R
/
F.Wide R
/
Surround R
/
S.Back R
z
/
S.Back L
z
/
Surround L
/
F.Wide L
/
Subwoofer
: Select the speaker.
z
When the “Speaker Config.” – “S.Back” setting (
v
page 75) is set to
“1spkr”, “S.Back” is displayed.
•
–12.0dB – +12.0dB
(0.0dB)
: Adjust the volume.
• When
o
is pressed while the subwoofer volume is set to “–12 dB”, the
“Subwoofer” setting switches to “OFF”.
• When “Channel Level” is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 51.
NOTE
• Speakers set to “None” in the “Speaker Config.” (
v
page 75) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
“Channel Level” is not displayed.
Default
: The “Channel Level” settings are returned to the default settings.
•
Yes
: Reset to the defaults.
•
No
: Do not reset to the defaults.
When you select “Default” and press
ENTER
, the “Default Setting?”
prompt is displayed. Select either “Yes” or “No”, and press
ENTER
.
