DEMA E-Royal Modest 2021, Operation And Maintenance Manual

Page: 57 / 60

4.2. Nastavitev parametrov
Priprava
Ko je zaslon aktiven, dvakrat pritisnite (interval <0,3
sekunde). Sistem bo vstopil v stanje nastavitve para -
metrov MENU, v katerem je mogoče nastaviti para -
metre prikaza. Ponovno dvakrat pritisnite (interval
<0,3 sekunde), da se vrnete v glavni meni. Če se 10
sekund ne izvede nobena operacija, se bo zaslon vrnil
na običajen prikaz vožnje. V stanju nastavitve parame -
trov, ko začne parameter, ki ga želite nastaviti, utripa -
ti, pritisnite + ali - za nastavitev vrednosti parametra.
Na kratko pritisnite , da preklopite med parametri, ki jih
želite nastaviti. Za izhod iz podmenija dvakrat pritisnite
(interval <0,3 sekunde).
Ponastavitev podatkov
Pritisnite dvakrat <0,3 sekunde) - zaslon vstopi v stanje
MENU. V polju za hitrost se prikaže tC . Če pritisnete, se pri -
kaže tudi „y“. Zdaj vse začasne podatke, npr. najvišjo hitrost
( MAXS ), povprečno hitrost ( AVG ) in enojno potovanje ( TRIP )
lahko počistite. Na kratko pritisnite (<0,3 sekunde) za vstop
v vmesnik za nastavitev km / milje. Če uporabnik ne ponasta -
vi podatkov, se posamezna razdalja potovanja in skupni čas
vožnje samodejno izbrišeta, ko skupni čas vožnje preseže 99
ur in 59 minut. Podatki se ne izbrišejo, ko je funkcija zaznava -
nja svetlobe na zaslonu nastavljena na 0 ali ko je izklopljena!
Km/Milje
Ko polje hitrosti prikaže S7 , pritisnite + in - , da preklo -
pite med km/h in mph, ali nastavite kilometre ali milje.
Po tej nastavitvi na kratko pritisnite (<0,3 sekunde), da
vstopite v nastavitveni vmesnik občutljivosti na svetlobo.
Privzeti prikaz je km.
Svetlobna občutljivost
Ko polje hitrosti prikaže bL0 , pritisnite + / - , da izberete števil -
ko med 0 in 5. Višja kot je izbrana številka, višja je občutljivost
na svetlobo. Po tej nastavitvi na kratko pritisnite (<0,3 se -
kunde), da vstopite v vmesnik za nastavitev osvetlitve ozadja.
Svetlost osvetlitve zaslona
Ko polje hitrosti prikaže bL1 , pritisnite + / - , da izberete
številko med 1 in 5. Slika 1 predstavlja najnižjo svetlost,
medtem ko 5 označuje najvišjo svetlost zaslona. Po tej na -
stavitvi na kratko pritisnite (<0,3 sekunde), da vstopite v
vmesnik za samodejni izklop.
Avtomatični izklop
Ko polje hitrosti prikaže OFF , pritisnite + / - , da izberete
številko med 1 in 9. Številke prikazujejo minute, ki so
potrebne za samodejno zaustavitev zaslona. Po tej na -
stavitvi na kratko pritisnite (< 0.3 seconds) to enter the
setting interface of maintenance warning.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10 〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10 〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10
〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
11
DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
Delovanje in navodila za vzdrževanje koles SI 57