DEMA E-Royal Modest 2021, Operation And Maintenance Manual

Page: 46 / 60

4.2. Paraméterek beállítása
Az értékek bevitelének előkészítése
Ha a kijelző aktív, nyomja meg kétszer az gombot (<0.3 má -
sodperc). A rendszer belép a MENU paraméterbeállítási üzem -
módba, amelyben a kijelző paraméterei állíthatók. Nyomja meg
ismét kétszer (intervallum <0.3 másodperc), hogy visszatérjen
a főmenübe. A paraméter beállítási üzemmódban, amikor a be -
állítani kívánt paraméter kezd el villogni, a +/- gomb megnyo -
másával állítsa be a paraméter értékét. Röviden nyomja meg a
gombot a kívánt paraméterek közötti váltáshoz. Nyomja meg
kétszer (<0.3 másodperc) az almenüből való kilépéshez. Ha
10 másodpercig nem hajtunk végre műveletet, a rendszer visz -
szatér az alapértelmezett menübe.
Az adatok visszaállítása
Nyomja meg kétszer (intervallum <0,3 másodperc) - a kijelző be -
lép a MENU -be. A sebességmezőben a tC jelenik meg. Ha meg -
nyomja a gombot, megjelenik egy „ y “ is. Most minden ideiglenes
adat, pl. a maximális sebesség ( MAXS ), az átlagsebesség ( AVG )
és az aktuális távolság ( TRIP ) törölhető. Nyomja meg röviden
(<0,3 másodperc) a km/mérföld beállításához. Ha a felhaszná -
ló nem állítja vissza az adatokat, az egyszeri utazási távolság és
a felhalmozott teljes menetidő automatikusan megszűnik, ha a
felhalmozott teljes menetidő meghaladja a 99 órát és 59 percet.
Km/mérföld
Amikor a sebességmező megjeleníti az S7 -et, nyomja meg a
+ / - gombot a km/h és az mph közötti váltáshoz, vagy km vagy
mérföld beállításához. A beállítás után nyomja meg röviden
(<0,3 másodperc) a fényérzékenység beállítási felületét. Az
alapértelmezett kijelzés km-ben van megadva.
Fényérzékenység
Ha a sebesség mező a bL0 értéket jeleníti meg, nyomja meg a
+ / - gombot a 0 és 5 közötti érték kiválasztásához. Minél ma -
gasabb a kiválasztott szám, annál nagyobb a fényérzékenység.
A beállítás után nyomja meg röviden (<0,3 másodperc) a hát -
térvilágítás fényerejének beállításához.
Háttérvilágítás fényereje
A Ha a sebességmező a bL1 értéket mutatja, nyomja meg a + / -
gombot az 1 és 5 közötti szám kiválasztásához. Az 1. ábra
a legalacsonyabb fényerőt jelöli, míg az 5 a legmagasabb
háttérvilágítású fényerőt jelzi. A beállítás után nyomja meg
röviden (<0,3 másodperc) az automatikus kikapcsolási idő
beállítási felületéhez.
Automatikus kikapcsolási idő
Amikor a sebességmezőben megjelenik az OFF felirat (Ki),
nyomja meg a + / - gombot az 1 és 9 közötti szám kiválasztá -
sához. Az számok jelzik a kijelző automatikus kikapcsolásá -
hoz szükséges perceket. A beállítás után nyomja meg röviden
az (<0,3 másodperc) gombot a karbantartási figyelmeztetés
beállítási felületéhez.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10
〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10 〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
10 DISPLAY MANUAL DP C10.UART
PARAMETER SETTING
• Items to be Set
1
〉 Data reset
2
〉 Km/mile
3
〉 Light sensitivity
4
〉 Display backlight brightness
5
〉 Automatic off time
6
〉 Maintenance warning settings
7
〉 Check wheel diameter
8
〉 Speed Limit Setting
9
〉 Speed model
10 〉 Battery infromation10 error code
• Setting Preparation
1) When the display is active, press
twice (interval < 0.3 seconds). The system
will enter the MENU parameter setting
state, in which the display parameters can
be set. Press
twice again (interval < 0.3
seconds) to return to the main menu.
2) If no operation is performed for 10 sec-
onds, the display will return to the normal
riding display.
3) In the parameter setting state, when the
parameter you want to set begins to flash,
press / to adjust the parameter value.
Briefly press
to switch between the pa-
rameters to be set. Press twice (interval
< 0.3 seconds) to exit the submenu.
• Data reset
Press twice (interval < 0.3 seconds) –
the display enters the MENU state. In the
speed field tC is displayed. If you press ,
a "y" is also displayed. Now all temporary
data, e.g. maximum speed (MAXS), average
speed (AVG) and single trip distance (TRIP)
can be cleared. Briefly press
(< 0.3 sec-
onds) to enter the km/mile setting interface.
If the user does not reset the data, the single
trip distance and the accumulated total rid-
ing time will be automatically cleared when
the accumulated total riding time exceeds
99 hours and 59 minutes.
* The data will not be cleared when the
display’s light-sensing function is set to 0 or
when it is switched off!
• Km/mile
When the speed field displays S7, press
/ to switch between km/h and mph, or
to set km or mile. After this setting, briefly
press
(< 0.3 seconds) to enter the
setting interface of light sensitivity. Default
display is km.
• Light Sensitivity
When the speed field displays bL0, press
/ to choose a figure between 0 and 5.
The higher the chosen figure, the higher the
light sensitivity.
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
11 DISPLAY MANUAL DP C10.UART
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
backlight brightness.
• Display Backlight Brightness
When the speed field displays bL1, press
/ to choose a figure between 1 and 5.
The figure 1 represents the lowest brightness
while 5 indicates the highest display back-
light brightness.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
automatic off time.
• Automatic Off Time
When the speed field displays OFF, press
/ to choose a figure between 1 and 9.
The figures indicate the minutes that it takes
to automatically shut down the display.
After this setting, briefly press (< 0.3
seconds) to enter the setting interface of
maintenance warning.
• Maintenance Warning (can be deacti-
vated)
When the speed field displays nnA, press
/ to choose either 0 or 1. 0 disables the
function while 1 enables it.
1) The display will prompt maintenance
necessity based on such information as the
accumulated riding distance and the battery
charge cycles.
2) When the accumulated total riding dis-
tance exceeds 5,000 km (can be customized
by the manufacturer), the display will show
the symbol
. When the display is
started up, the sign for accumulated riding
distance will flash for 4 seconds, indicating
that maintenance is necessary.
3) When the number of battery charge cy-
cles exceeds 100 (can be customized by the
manufacturer), the display will the symbol
. When the display is started up,
the sign for battery will flash for 4 seconds,
indicating that maintenance is necessary.
4) The maintenance alert function can be
disabled: settings ->maintenance alert (MA)
-> 0. (Maintenance alert can also be set via
a computer. This requires a USB connection.
See also the parameter setting instructions).
PARAMETER SETTING
HU 46 Használati útmutató Használati útmutató