DELTA DORE TTGSM TYXAL+, Installation Manual

Page: 71 / 232

71
EN
70
1 2 3
4 5 6
7 8 9
0
1 2 3
1 2 3
4 5 6
7 8 9
0
1 2 3
4 5 6
7
*
#
8 9
0
10. Correct operation test
With an alarm control unit:
Switch on the system, and trigger an intrusion.
In autonomous mode:
For example, on a water leak detector, simulate a water
leak by placing water above it.
On the transmitter:
1
n°1
n°2
2
n°3
3
n°4
4
n°5
5
n°6
6
7
n°1
n°2
8
n°3
9
n°4
10
n°5
11
n°6
12
13
n°1
n°2
14
n°3
15
n°4
16
To view the defect details,
type 1
To disable the product,
press 1
"You are
connected with
a telephone
transmitter"
Test call
04 April 2014
To stop the call cycle,
press
- the system is off - to
listen, press 2
- to listen whilst talking,
press 3
- to disconnect the call,
press twice
Leak technical defect
on the detector
zone 2, on 04 April 2014.
Check that the telephone transmitter calls the programmed num-
bers (6 at most) one after the other until a contact picks up:
- the transmitter requires you to press the button,
- it reads the voice message and specifies the type of defect,
- It asks if you want to listen to what is happening, speak to a
person close to the transmitter, stop the call cycle and obtain
the details of the defects if an alarm control unit is associated.
Create a detection event to check that the installation works correctly.
You can also trigger a test call cycle by
pressing the transmitter's button for 30
seconds.
>30s
Example of a full cycle
with 6 programmed numbers
Configuration menu
Enter the new call number and press
Configuration menu Enter the new call number and press Action accepted
To modify the access code, press 3
Configuration menu Enter your access code Enter the new access code
To personalise the voice message, press 2
This is the configured voice message:
“You are connected with a telephone
transmitter”
- To modify the voice message, press 1.
- To return to the previous menu, press This is the configured voice message:
“You are connected with a telephone
transmitter”
- To modify the voice message, press 1.
- To return to the initial voice message,
press 2.
- To return to the previous menu, press Please speak after the tone, then press
a key to stop recording.
To modify the date or time, press 4
To configure the number of rings, press 5
( TTRTC TYXAL+ only)
To change the language, press 6.
To select French, press 1.
To select English, press 2.
To select Spanish, press 3.
To select German, press 4.
To select Italian, press 5.
To select Polish, press 6.
To select Dutch, press 7.
- For the number 1, press 1.
- For the number 2, press 2.
- For the number 3, press 3.
- For the number 4, press 4.
- For the number 5, press 5.
- For the number 6, press 6.
- To return to the previous menu, press
No call number is configured.
To configure it, press 1.
- To return to the previous menu, press
This is the configured number:
02.99.73.xx.xx
To modify it, press 1.
To delete it, press 2.
- To return to the previous menu, press
This is the configured date:
29 November 2013,
This is the configured time: 11h57.
- To modify the date, press 1.
- To modify the time, press 2.
- To return to the previous menu, press 29 November 2013, 11h57.
- To modify the date, press 1.
- To modify the time, press 2.
- To return to the previous menu, press Enter the 6 date digits
Enter the 4 time digits
To select the AM format, press 1
To select the PM format, press 2
This is the configured number of rings: 10
- To modify it, press 1.
- To return to the previous menu, press Enter the 2 digits for the new number
of rings
Action accepted
Configuration menu Action accepted
Action accepted
Action accepted
This is the configured
number...
Enter the 4 time digits
9. Operation in autonomous mode