Dell Studio 1536 Service Manual Download Page 33

Page: 33 / 41

Great user manuals database on

Replacing the Mini-Card

Follow the instructions in

Remove the new Mini-Card from its packaging.

Insert the Mini-Card connector at a 45-degree angle into the appropriate system board connector. For example, the WLAN card connector is labeled

WLAN

and so on.

Press the other end of the Mini-Card down into the slot and replace the securing screw.

Connect the appropriate antenna cables to the Mini-Card you are installing. The following table provides the antenna cable color scheme for each Mini-
Card supported by your computer.

Secure the unused antenna cables in the protective mylar sleeve.

Replace the base cover and tighten the captive screws.

Slide the battery into the bay until it clicks into place.

Install the drivers and utilities for your computer, as required. For more information, see the

Dell Technology Guide

NOTICE:

When the Mini-Card is not in the computer, store it in protective antistatic packaging. For more information, see "Protecting Against

Electrostatic Discharge" in the safety information that shipped with your computer.

NOTICE:

Install the UWB Mini-Card in the WWAN or WPAN slot. Do not install a UWB Mini-Card in the WLAN card slot. Doing so may cause damage to

your computer.

NOTICE:

Use firm and even pressure to slide the card into place. If you use excessive force, you may damage the connector.

Connectors on the Mini-Card

Antenna Cable Color Scheme

WWAN (2 antenna cables)

Main WWAN (white triangle)

Auxiliary WWAN (black triangle)

white with gray stripe

black with gray stripe

WLAN (2 or 3 antenna cables)

Main WLAN (white triangle)

Auxiliary WLAN (black triangle)

MIMO WLAN (*gray triangle)

white

black

gray

WPAN (one antenna cable)

WPAN

blue

* The MIMO WLAN is optional and may not be available in all computers.

NOTE:

The gray antenna cable may not be available in all computers. The presence of the gray antenna cable in your Mini-Card compartment

depends upon the type of display.

NOTE:

If you are installing a communication card from a source other than Dell, you must install the appropriate drivers and utilities. For more

information, see the

Dell Technology Guide

Summary of Contents for Studio 1536










































Search results

Summary of Contents for Studio 1536

Reviews:

Related manuals for Studio 1536

Brands by name

Popular brands

Dell Studio 1536, Service Manual

Search results

Summary of Contents for Studio 1536

Reviews:

Related manuals for Studio 1536

Brands by name

Popular brands