Dell Precision 3510 Service Manual Download Page 4

Page: 4 / 78

1 Working on your computer............................................................................................................ 6

Safety instructions.................................................................................................................................................................6

2 Technology and components........................................................................................................10

3 Major components of your system................................................................................................16

4 Disassembly and reassembly........................................................................................................ 18

MicroSD card........................................................................................................................................................................18

Removing the microSD card......................................................................................................................................... 18
Installing the microSD card........................................................................................................................................... 19

SIM card................................................................................................................................................................................ 19

Removing the SIM card.................................................................................................................................................19
Installing the SIM card................................................................................................................................................... 21

Base cover.............................................................................................................................................................................21

Removing the base cover..............................................................................................................................................21
Installing the base cover............................................................................................................................................... 23

Battery.................................................................................................................................................................................. 25

Memory modules................................................................................................................................................................. 27

Removing the memory module.................................................................................................................................... 27
Installing the memory modules.....................................................................................................................................28

WLAN card...........................................................................................................................................................................30

Removing the WLAN card............................................................................................................................................30
Installing the WLAN card...............................................................................................................................................31

WWAN card......................................................................................................................................................................... 32

Removing the WWAN card.......................................................................................................................................... 32
Installing the WWAN card.............................................................................................................................................33

Coin-cell battery.................................................................................................................................................................. 34

Removing the coin-cell battery....................................................................................................................................34
Installing the coin-cell battery...................................................................................................................................... 34

DC-in port.............................................................................................................................................................................35

Removing the DC-in......................................................................................................................................................35

Contents

Summary of Contents for Precision 3510















































































Search results

Summary of Contents for Precision 3510

Reviews:

Related manuals for Precision 3510

Brands by name

Popular brands

Dell Precision 3510, Service Manual

Search results

Summary of Contents for Precision 3510

Reviews:

Related manuals for Precision 3510

Brands by name

Popular brands