Ethernet Service Port Procedures
To update the drive’s firmware using the ethernet interface:
Note:
The drive uses a limited version of FTP protocol to communicate on the
ethernet interface. It is recommended to use a simple, command line FTP
session, such as the DOS command prompt, when communicating with the
drive. This product is not intended to be connected directly or indirectly by
any means whatsoever to interfaces of public telecommunications networks.
When the IP address has been changed to the customer LAN or DHCP has
obtained a new address, the default address of the tape drive will still be
available. This does not create a LAN conflict as the customer LAN address
takes operational preference. The default address will not conflict with other
drives having the default address. When the drive comes online the drive
checks if the default address is on the LAN and will not become active
while another drive is active. This is acceptable operation and at times a
multi-drive LAN may see different drives with accessible default address.
1.
Obtain the latest drive firmware from the web. Go to http://support.dell.com.
2.
Connect an ethernet patch cable to the drive’s ethernet interface and to a
computer. In order to meet electromagnetic immunity requirements, a shielded
ethernet cable is required.
3.
Create an FTP session between the drive and the computer. The drive’s default
IP address: 1
69.254.0.3
.
4.
At the user prompt, type
guest
and press
Enter
.
5.
At the password prompt, press
Enter
. No response is needed.
6.
Type
bin
to set the communication mode to binary.
7.
Type
put firmware name
to transfer the firmware to the drive. Replace
firmware
name
with the actual firmware file name. The drive will reset automatically
when the transfer is complete and the FTP session will be lost. Type
quit
to end
the FTP session.
8.
After the drive resets, the new firmware will be loaded on the drive.
9.
Remove the ethernet patch cable from the drive’s ethernet interface.
Capturing a drive dump using the ethernet interface
Another way to capture a drive dump is using the ethernet port. To capture a
dump on the drive using the ethernet interface follow the steps below.
Note:
The drive uses a limited version of FTP protocol to communicate on the
ethernet interface. It is recommended to use a simple, command line FTP
session, such as the DOS command prompt, when communicating with the
drive. This product is not intended to be connected directly or indirectly by
any means whatsoever to interfaces of public telecommunications networks.
1.
Connect an ethernet patch cable to the drive’s ethernet interface and to a
computer. In order to meet electromagnetic immunity requirements, a shielded
ethernet cable is required.
2.
Create an FTP session between the drive and the computer. The drive’s default
IP address:
169.254.0.3
.
3.
At the user prompt, type
guest
and press
Enter
.
4.
At the password prompt, press
Enter
. No response is needed.
5.
Type
bin
to set the communication mode to binary.
6.
Type
mget *.dmp
to transfer a drive dump to the computer. If a dump already
exists, the drive will show you the dump name and ask if you want to transfer
2-8
Dell PowerVault LTO Tape Drive User's Guide
Summary of Contents for PowerVault LTO5-140
