Dell PowerVault 750N System Administrator Manual Download Page 85

Page: 85 / 156

System Recover y, Backup, and Restore

5-13

Click

Update Driver

The

Upgrade Device Driver Wizard

displays.

Click

Next

Click the radio button next to

Search for a suitable driver for my device

(recommended)

and then click

Next

Optional search locations

, click the checkbox for

Specify a location

Deselect the other checkboxes.

Click

Next

The

Properties

dialog box displays.

Specify the folder name that contains the device drivers in the path for

Copy

manufacturer's files from

Click

and then click

Next

The

Upgrade Device Driver Wizard

searches the specified folder for the driver files.

Make sure the wizard has selected the appropriate PowerVault tape device and click

Next

Click

Finish

Click

Close

to exit the driver properties dialog box.

Installing Drivers for PowerVault Tape Drive Media Changers

To install drivers for tape media changers when using Windows 2000 backup and recovery
tools, perform the following steps.

Connect the PowerVault tape device and restart the machine.

Connect to the PowerVault NAS Manager.

Click

Maintenance

and then click

Terminal Services

Terminal Services Client

session.

In the

Advanced Administration Menu

, click

Computer Management

under

System

Management

Click

Computer Management

in the left pane, and then click

System Tools.

Click

Device Manager

in the left pane.

Click

Medium Changers

in the right pane.

Summary of Contents for PowerVault 750N





























































































































































Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands

Dell PowerVault 750N, System Administrator Manual

Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands