Dell PowerVault 750N System Administrator Manual Download Page 86

Page: 86 / 156

5-14

System Recover y, Backup, and Restore

.co

ll.c

Double-click

Unknown Medium Changer

Click

Driver

in the

Properties

window.

Click

Update Driver

The

Upgrade Device Driver Wizard

displays.

Click

Next

Click the radio button next to

Search for a suitable driver for my device

(recommended)

and then click

Next

Optional search locations

, click the checkbox for

Specify a location

Deselect the other checkbox.

Click

Next

A dialog box displays with a field for you to enter the location of the device driver.

In the path for

Copy manufacturer's files from

, specify the folder name that contains

the device drivers, and click

Click

Next

The

Upgrade Device Driver Wizard

searches the specified folder for the driver files.

Make sure the

Upgrade Device Driver Wizard

has selected the appropriate PowerVault

tape device and click

Next

Click

Finish

Click

Close

Summary of Contents for PowerVault 750N





























































































































































Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands

Dell PowerVault 750N, System Administrator Manual

Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands