Dell PowerVault 750N System Administrator Manual Download Page 141

Page: 141 / 156

Online Ser ver Diagnostics

8-5

• To run diagnostics on a remote appliance on the network, specify the IP address of the

remote appliance in the

Remote IP Address

box, and then click

Run diagnostics on

specified IP

In the remote login window, type the user ID of a local administrator group member

for the specified appliance in the

User Name

box, and click

Login

This action opens the main window, from which you may select and run diagnostic

tests.

Configuring Online Server Diagnostics

Server Diagnostics enables you to set the preferred options for running diagnostic tests.

To set the options in Server Diagnostics, perform the following steps:

If you have not already done so, start the Server Diagnostics.

Specify a target NAS appliance.

In the main window, click

Advanced Settings

In the

Advanced Settings

window, set the options you need. See “Advanced Settings”

for a description of each option.

Running Online Server Diagnostics

To run a diagnostic, perform the following steps:

If you have not already done so, start the Server Diagnostics.

Specify a target NAS appliance.

In the main diagnostics window, use the component selector to specify the

components you want to test.
• Use the diagnostic tree to select the individual tests you want to run.
• Click

Select All

to select all tests in the tree. To erase your selections, click

Clear

All

Click

Next

The

Progress

window opens and the diagnostic tests begin. Use the progress viewer to

monitor the success or failure of each test.

When the tests finish, click

View Log

to see detailed results for each test.

Summary of Contents for PowerVault 750N





























































































































































Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands

Dell PowerVault 750N, System Administrator Manual

Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands