Dell PowerVault 750N System Administrator Manual Download Page 88 | Manualshive

Page: 88 / 156

background image

6-2

Dell ActiveArchive™

w

w

w

.d

e

ll

.co

m

|

s

u

p

p

o

rt

.d

e

ll.c

o

m

Dell ActiveArchive allows the creation and preservation of persistent images of Dell
PowerVault™ 750N and 755N system data volumes. The Dell ActiveArchive software is
installed on all PowerVault 75

x

N systems. It can be configured by using the NAS Manager.

This chapter provides information on the following topics:

• Introduction to persistent images
• Scheduling persistent images
• Adding persistent images to the schedule
• Deleting a persistent image schedule
• Editing the properties of a persistent image’s schedule
• Taking a new persistent image
• Deleting a persistent image
• Configuring the persistent image environment
• Setting persistent image retention weights
• Accessing persistent images
• Restoring a volume

Introduction to Persistent Images

A persistent image is a point-in-time copy of a disk volume. Unlike conventional volumes,
the information in the persistent image is static. A persistent image contains an exact copy
of the file system at the time the persistent image was created. If you change a file on the
active file system after taking a persistent image, the persistent image contains the old
version of the file. If an active file gets corrupted or deleted, you can restore the old version
by copying the file from the latest persistent image. Also, because the persistent image
contains the contents of the file system when the persistent image was taken, you can
perform a backup from the persistent image without stopping all I/O to the file servers, thus
eliminating the backup window required by other types of backup.

NOTE:

Persistent images are temporary backups of your data that reside on the same volume as

your data. If the volume becomes damaged, you lose your data including the persistent image.
Therefore, persistent images do not replace regular backups of your volume.

«
...
86
87
88
89
90
...
»

Summary of Contents for PowerVault 750N





























































































































































Reviews:

No comments

Related manuals for PowerVault 750N

Mobile Ultra Memory Stick Micro

Brand: SanDisk Pages: 1

Brand: GSi Pages: 84

Brand: Seagate Pages: 46

Brand: Dancover Pages: 66

F5U100-ORG - USB Busstation Hub

Brand: Belkin Pages: 12

Brand: Brookstone Pages: 8

HTS421210H9AT00

Brand: Hitachi Pages: 239

HTS541010G9AT00 - Travelstar 100 GB Hard Drive

Brand: Hitachi Pages: 2

HTS541010G9AT00 - Travelstar 100 GB Hard Drive

Brand: Hitachi Pages: 2

Brand: Quantum Pages: 4

SuperLoader 3A Series

Brand: Quantum Pages: 121

Brand: Fantom Drives Pages: 10

Brand: Life Fitness Pages: 30

Brand: Karibu Pages: 48

Rugged Hard Disk

Brand: LaCie Pages: 47

Constellation Constellation ST4000NM0053

Brand: Seagate Pages: 88

Brand: Seagate Pages: 92

Cheetah ST3146854

Brand: Seagate Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands