Dell PowerVault 750N System Administrator Manual Download Page 140

Page: 140 / 156

8-4

Online Ser ver Diagnostics

.co

ll.c

Click

Next

When the

InstallShield Wizard

completes installing the files, click

Finish

Installing the JAVA Runtime Environment

If your system does not have the Java 2 Runtime Environment installed on it, you will be
asked whether you want to install it the first time you run the Online Server Diagnostics.

Because the Java 2 Runtime Environment is needed to run the Online Server

Diagnostics, click

Yes

Click

Yes

to accept the agreement.

Click

Next

After the installation is completed, you can run the Online Server Diagnostics.

Using the Online Server Diagnostics

This section explains how to start, configure, and run your server diagnostics:

Starting the Online Server Diagnostics

To start the diagnostics, perform one of the following procedures:

On the NAS Manager primary menu, click

Maintenance

Click

Online Server Diagnostics

Specifying a Target Appliance

NOTE:

Online Server Diagnostics must be installed on both the remote appliance and the local

appliance.

To specify the NAS appliance on which you want to run diagnostic tests (the target),
perform the following steps:

If you have not already done so, start the diagnostics.

In the

Welcome

window, perform one of the following tasks:

• To run diagnostics on the local server, click

Run diagnostics on

NNN.NNN.NNN.NNN

Summary of Contents for PowerVault 750N





























































































































































Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands

Dell PowerVault 750N, System Administrator Manual

Search results

Summary of Contents for PowerVault 750N

Reviews:

Related manuals for PowerVault 750N

Brands by name

Popular brands