Dell Inspiron 23 Service Manual Download Page 95

Page: 95 / 106

Boot

Load Legacy

OPROM

Allows you to load the legacy OPROM when in the UEFI

boot mode. (Never by default).

Keyboard Errors

Allows you to enable or disable the display of keyboard-
related errors during boot — Report or Do Not Report
(Report by default).

USB Boot
Support

Allows you to enable or disable booting from USB mass
storage devices such as external hard drive, optical drive,
USB key, and so on — Enable or Disable (Enabled by
default).

Boot Mode:

1st Boot
Device

Displays the first boot device.

2nd Boot
Device

Displays the second boot device.

3rd Boot

Device

Displays the third boot device.

4th Boot

Device

Displays the fourth boot device.

5th Boot

Device

Displays the fifth boot device.

Hard Disk Drivers Displays the boot sequence of the hard drive.

USB Storage

Drivers

Displays the boot sequence of the USB storage drive.

CD/DVD ROM

Drivers

Displays the boot sequence of the optical drive.

Power

Wake Up by

Integrated LAN/
WLAN

Allow the computer to be powered on by special LAN or

wireless LAN signals — Enabled or Disabled (Disabled by
default).

NOTE: This option can be enabled only if the Deep
Sleep Mode is set to Disable.

AC Recovery

Allows you to configure the behavior of your computer

after it recovers from a power failure — Power Off, Power
On, or Last Power State (Power Off by default).

Summary of Contents for Inspiron 23











































































































Search results

Summary of Contents for Inspiron 23

Reviews:

Related manuals for Inspiron 23

Brands by name

Popular brands

Dell Inspiron 23, Service Manual

Search results

Summary of Contents for Inspiron 23

Reviews:

Related manuals for Inspiron 23

Brands by name

Popular brands