Dell Inspiron 1318 Service Manual Download Page 42

Page: 42 / 46

Back to Contents Page

Wireless Switch Assembly

Dell™ Inspiron™ 1318 Service Manual

Removing the Wireless Switch Assembly

Replacing the Wireless Switch Assembly

Removing the Wireless Switch Assembly

Follow the instructions in

Before You Begin

Remove the system board (see

System Board

Remove the two M2 x 3-mm screws from either side of the wireless switch assembly board and lift it away from the computer base.

Replacing the Wireless Switch Assembly

Secure the wireless switch assembly board to the computer base by replacing the two M2 x 3-mm screws.

Replace the system board (see

System Board

Slide the battery into the battery bay, until it clicks into place.

Back to Contents Page

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions shipped with your computer.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

Handle components and cards by their edges, and avoid touching pins and contacts.

1 M2 x3-mm screws

(2)

2 wireless switch assembly

board

3 wireless switch assembly cable

connector

Summary of Contents for Inspiron 1318















































Search results

Summary of Contents for Inspiron 1318

Reviews:

Related manuals for Inspiron 1318

Brands by name

Popular brands

Dell Inspiron 1318, Service Manual

Search results

Summary of Contents for Inspiron 1318

Reviews:

Related manuals for Inspiron 1318

Brands by name

Popular brands