Dell Inspiron 1318 Service Manual Download Page 13 | Manualshive

Page: 13 / 46

background image

Back to Contents Page

Coin-Cell Battery

Dell™ Inspiron™ 1318 Service Manual

Removing the Coin-Cell Battery

Replacing the Coin-Cell Battery

Removing the Coin-Cell Battery

1.

Follow the procedures in

Before You Begin

2.

Remove the module cover (see

3.

The battery is glued to the computer, use a plastic scribe to pry the coin-cell battery from the slot.

4.

Disconnect the coin-cell battery cable from the system board connector.

Replacing the Coin-Cell Battery

1.

Connect the coin-cell battery cable to the system board connector.

2.

Peel off the adhesive on the coin-cell battery and adhere it to the system board.

3.

Replace the module cover (see

4.

Slide the battery into the battery bay, until it clicks into place.

Back to Contents Page

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions shipped with your system.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as a connector on the back of the computer).

NOTICE:

To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the

computer.

1

coin-cell battery cable connector

2

coin-cell battery

«
...
11
12
13
14
15
...
»

Summary of Contents for Inspiron 1318















































Reviews:

No comments

Related manuals for Inspiron 1318

Brand: IBM Pages: 230

Brand: Datalogic Pages: 88

Brand: VALKPC Pages: 20

Brand: WAGO Pages: 52

Brand: XtendLan Pages: 17

ZBOX PRO ZP-QK7P3000

Brand: Zotac Pages: 25

Brand: Packard Bell Pages: 122

Brand: MSI Pages: 71

Brand: Casio Pages: 81

Brand: Tangent Pages: 14

NetVista A40i 2251

Brand: IBM Pages: 98

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

VPCL117FX - Vaio L Series All-in-one Touch Screen

Brand: Sony Pages: 2

VPCL112GX - Vaio L Series All-in-one Touch Screen

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands