Dell Inspiron 1318 Service Manual Download Page 19 | Manualshive

Page: 19 / 46

background image

6.

Remove the keyboard (see

7.

Pull the display cable tab to disconnect the display cable from the system board connector.

8.

Disconnect the camera cable from the system board connector.

9.

Make note of the cable routing and carefully dislodge the antenna cables and the rest of the cables from their routing guides. Pull the cables away, so
that they are clear of the palm rest.

10.

Remove the two M2.5 x 5-mm screws from either side of the display assembly.

11.

Lift and remove the display assembly from the computer base.

Replacing the Display Assembly

1.

Route and connect the display cable to the connector on the system board.

2.

Route and connect the camera cable to the connector on the system board.

3.

Carefully route the WLAN antenna cables into their routing guides on the palm rest and through the computer base.

4.

Replace the two M2.5 x 5-mm screws on each side of the display assembly.

5.

Replace the keyboard (see

).

NOTE:

Note how the display cable and the camera cable have been routed through their routing guides.

1

camera cable

2

display cable

«
...
17
18
19
20
21
...
»

Summary of Contents for Inspiron 1318















































Reviews:

No comments

Related manuals for Inspiron 1318

Brand: Igel Pages: 2

Brand: FabiaTech Pages: 65

Brand: Asus Pages: 52

AAEON BOXER-8251AI

Brand: Asus Pages: 39

Aaeon BOXER-8170AI

Brand: Asus Pages: 35

AAEON RTC-1010M

Brand: Asus Pages: 55

AAEON RTC-710RK

Brand: Asus Pages: 43

Brand: Asus Pages: 38

AAEON BOXER-8240AI

Brand: Asus Pages: 53

Brand: Asus Pages: 76

Brand: Asus Pages: 44

Brand: Asus Pages: 76

AAEON BOXER-8231AI

Brand: Asus Pages: 38

AAEON BOXER-8521AI

Brand: Asus Pages: 54

AAEON BOXER-8223AI

Brand: Asus Pages: 47

Brand: Asus Pages: 68

Brand: Asus Pages: 30

AAEON BOXER-8250AI

Brand: Asus Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands