Dell G5 15 Service Manual Download Page 36

Page: 36 / 112

Removing the computer base

WARNING:

Before working inside your computer, read the safety information that shipped with your computer and follow the

steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside

your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Topics:

•

Prerequisites

•

Procedure

Prerequisites

Remove the

Remove the

Remove the

Remove the

Procedure

Using pull tab, disconnect the camera cable from the system board.

Peel the camera cable off the computer base.

Remove the antenna cables from the routing guides on the computer base.

Remove the screw (M2x3) that secures the display-cable bracket to the computer base.

Lift the display-cable bracket off the computer base.

Using the pull tab, disconnect the display cable from the system board.

Remove the display cable from the routing guides on the computer base and peel the display cable off the computer base.

Open the latch and disconnect the power-button board cable from the system board.

Removing the computer base

Summary of Contents for G5 15

















































































































Search results

Summary of Contents for G5 15

Reviews:

Related manuals for G5 15

Brands by name

Popular brands

Dell G5 15, Service Manual

Search results

Summary of Contents for G5 15

Reviews:

Related manuals for G5 15

Brands by name

Popular brands