manualshive.com logo in svg

Dell Brocade 815, Troubleshooting Manual, Page: 163 / 172

Share
Download
Dell Brocade 815 Troubleshooting Manual Download Page 163

Brocade Adapters Troubleshooting Guide

139

53-1002145-01

HCM and Installer Message Reference

B

Please free up at least 50MB in the /opt directory and 
try the installation again.

Occurs when the space in 
the /opt directory is less 
than 50MB.

Free at least 50MB and 
then proceed with 
installation.

Please note that your system is Windows 2003 x86 
Service Pack 1.
There is no brocade adapter driver available for 
Windows 2003Service Pack 1. 

Please get Service Pack 2 from:
http://www.microsoft.com/downloads/details.aspx?Fa
milyID=95ac1610-c232-4644-b828-c55eec605d55&d
isplaylang=en 

Occurs when you install 
the driver on a Windows 
2003 x86 SP1 system.

Upgrade SP1 to SP2, and 
then try installing the 
driver.

Please note that your system is Windows 2003 x64 
Service Pack 1.
There is no brocade adapter driver available for 
Windows 2003Service Pack 1. 

Please get Service Pack 2 from:
http://www.microsoft.com/downloads/details.aspx?Fa
milyID=95ac1610-c232-4644-b828-c55eec605d55&d
isplaylang=en 

Occurs when you install 
the driver on a Windows 
2003 x64 SP1 system.

Upgrade SP1 to SP2, and 
then try installing the 
driver.

ReStart Message For Solaris

SUCCESSFUL installation of Driver may require System 

Occurs in all Solaris 
systems when the driver 
is installed successfully.

Restart the system to 
complete installation.

ReStart Message For Linux

Please reboot your system for the new driver to get 
loaded.

Occurs when the driver is 
installed successfully on 
Linux systems.

Restart the system to 
complete installation.

ReStart Message For Solaris

SUCCESSFUL uninstallation of driver may require 
System 

Occurs for Solaris 
systems when the driver 
is successfully removed.

Restart the system to 
complete removal.

ReStart Message For Linux

SUCCESSFUL uninstallation of driver may require 
System 

Occurs on Linux systems 
when the driver is 
successfully removed.

Restart the system to 
complete removal.

System dependencies not available.
GCC and Kernel rpms are required for installing Storage 
and Network Driver and HCM and Storage and Network 
Driver.
Variable 
"LOAD_UNSUPPORTED_MODULES_AUTOMATICALLY" in 
/etc/sysconfig/hardware/config file is set to “no”, 
please change it to “yes” before continuing installation 
otherwise the driver module will not be loaded.

Occurs when you install a 
drivers on a Linux system 
that does not contain GCC 
and Kernel rpm and when 
the variable 
"LOAD_UNSUPPORTED_M
ODULES_AUTOMATICALLY
" in 
/etc/sysconfig/hardware/
config file is set to “no”.

Change the “No” in 
variable  
"LOAD_UNSUPPORTED_M
ODULES_AUTOMATICALLY" 
present in 
/etc/sysconfig/hardware/
config file to “Yes.” 

Load the GCC and Kernel 
rpms onto the system and 
install the drivers. 

TABLE 15

Brocade Adapter Software Installer messages (continued)

Message

Cause

Corrective Action or Notes

Summary of Contents for Brocade 815













































































































































































Reviews:

No comments