Dell Alienware m17 R2 Service Manual Download Page 9

Page: 9 / 70

Table 1. Screw list(continued)

Component

Secured to

Screw type

Quantity

Screw image

Left I/O-board

Palm-rest assembly

M2x3

Right I/O-board

connector

•

System board

•

Right I/O-board

M2x3

Right I/O-board

Palm-rest assembly

M2x3

Fans

Palm-rest assembly

M2.5x5

System board

Palm-rest assembly

M2x3

Fan and heat-sink

assembly

System board

M2x3

Solid-state drive support

bracket

Palm-rest assembly

M2x1.9

Touchpad

Palm-rest assembly

M2x1.9

Power-adapter port

bracket

Palm-rest assembly

M2x3

Power-button assembly

Palm-rest assembly

M2x1.9

Keyboard bracket

•

Palm-rest assembly

•

Keyboard

M1.2x2.1

Keyboard

Palm-rest assembly

M1.2x1.6

Base cover

Removing the base cover

Prerequisites
1. Follow the procedure in

Before working inside your computer

About this task
The following image indicates the location of the base cover and provides a visual representation of the removal procedure.

Summary of Contents for Alienware m17 R2







































































Search results

Summary of Contents for Alienware m17 R2

Reviews:

Related manuals for Alienware m17 R2

Brands by name

Popular brands

Dell Alienware m17 R2, Service Manual

Search results

Summary of Contents for Alienware m17 R2

Reviews:

Related manuals for Alienware m17 R2

Brands by name

Popular brands